AEG 74740 manual Compensate for Floor Unevenness

Page 46

Setting up and connection instructions

Compensate for Floor Unevenness

3	Automatic Adjustment Foot: Your washing machine's rear left foot is
	of a spring leg design. This guarantees good stability of the unit, even

at high spinning speeds.

If the washing machine still does not stand firmly enough during spin- ning, proceed as follows:

01. Adjust the three adjustment feet

to the setpoint 10mm. To do this,

use the supplied special button to remove the transport safeguard.

If the automatic adjustment foot still does not reach the floor:

2. Manually extend the automatic adjustment foot (rear left) by the

necessary amount.

3. If necessary, check the setting with a spirit level.

Attention! Never use wood, card or similar underlays to compen-

sate for minor floor unevenness. Always use the adjustable screw-type feet of the machine.

46

Image 46

Contents ÖKO-LAVAMAT 74740 update To any subsequent owners of the unit Dear customerPlease read this user information carefully Practical use of the unitContents Remedying Faults What to do ifPage Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control Panel Program SelectorWool WOLLE, LAINE/ P Handwash Minutes. This is followed automatically by the main wash Come effective at higher temperaturesAdditional Program Buttons Shorter washing cycle for slightly dirty washingConsumption Values and Time Requirements What Does Update Mean? Water Protection Aqua ControlPrepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water SoftenerBrief Instructions Run a Washing CycleAfter the Washing Program Ends Setting the Washing Program TablesRevolutions Change Spin Speed / Select Rinse HoldPer minute Set the Delay Timer/Soaking Duration Soaking DurationOpening and Closing the Filling Door Add the WashingCompartment for pre-wash agent/soaking agent If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Or for water softenerIs pressed Start the Washing ProgramIf the time preselection is set Program sequence display Completion of the Washing ProgramMultidisplay Select the Additional Program Changing a Washing ProgramChanging or aborting a program Change the Spin SpeedWashing Cycle Ended/Remove Washing Program Tables WashingType Separate Rinse Separate Conditioning/Starching/ImpregnatingSeparate Spin Cleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpRemedying Faults What to do ifRINSE+ SPÜLEN+ Repasser Rinse Spülen If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Additional Rinse RINSE+/SPÜLEN+/RINCAGE+ When all the washing solution has drained offCancel Additional Rinse Set Additional RinseFeature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety FeatureSetting up and connection instructions Safety Instructions for InstallationWhen transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the UnitFirmly pull both hose holders off the unit Close off the hole with the plug cap GSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Delivery Heads over 1m Technical DataDimensions Measurements in mmSchweiz Suisse Svizzera Page Page Index Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG