AEG 82730 manual What Does Update Mean?, Water Protection Aqua Control + Aqua Alarm

Page 14

Instructions for use

Running Time Display

3	The running times of the washing programs
	depend on the usual washing practice and

the ambient conditions at the installation location.

The washing type and quantity, the type of washing powder, the water temperature and the room temperature etc. can influence the duration of the washing program.

The washing machine saves from each program the running times of the last wash cycles and calculates from them the average running time for a washing cycle. This average running time is shown by the multi display during the next wash.

After several washes, the running time shown in the multi display is thereby adapted to the usual washing practice and the ambient conditions at the installation location.

What Does ”Update” Mean?

The washing programs of your washing machine are controlled by soft- ware.

New types of textiles or new washing powders/liquids could, in the fu- ture, require new washing programs. The software can be adapted to these in most cases.

For further information on the ”Update”, consult the Customer Service. You can also ask the Customer Service about the costs of an ”Update”.

Water Protection Aqua Control +

Aqua Alarm

In the event of damage to the supply hose, the system blocks the fur- ther supply of water to the unit directly st the water tap.

If water escapes elsewhere, the drainage pump automatically pumps off – even if the unit is switched off. The washing machine merely has to be connected to the electricity mains. When the water protection system responds, a warning signal sounds at the same time.

14

Image 14

Contents

ÖKO-LAVAMAT 82730 update Dear customer Contents Solution Cooling What to do ifPage Correct Use SafetyBefore Putting into Operation for the First Time Child Safety General SafetyDispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clipsDrawer for Washing Powder and Care Agent Unit DescriptionFront View Control Panel Program SelectorWool WOL, LAINE/ P Handwash Program Silk ZIJDE, SOIE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean?Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes How much washing detergent and care agent? Water SoftenerSet the Washing Program Run a Washing CycleBrief Instructions After the Washing Program EndsRevolutions Change Spin Speed / Select Rinse HoldIf necessary, change the spin speed for the final Per minuteOff Set the Delay TimerOpening and Closing the Filling Door Red The door is openAdd the Washing For information on the correct preparation of the washingCompartment for pre-wash agent/soaking agent If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Or for water softenerStart the Washing Program If the time preselection is setCompletion of the Washing Program Washing Cycle Ended/Remove WashingLights up, too much washing detergent was used Program Tables WashingDelicates Soaking Separate Conditioning/Starching/Impregnating Separate SpinCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Aid of the emergency unlocking facility When all the washing solution has drained offEmergency Unlocking of the Filling Door Gency unlocking and remove the plug from the mainsTo rinse with more water No additional rinse is set when the unit is deliveredAdditional Rinse RINSE+ Set Additional RinseSet the Solution Cooling Solution CoolingCancel Additional Rinse Additional Rinse and Solution Cooling Cancel the Solution CoolingProgram Saving Setting the Program Saving FunctionCanceling the Program Saving Function Feature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety FeatureSetting up and connection instructions Safety Instructions for InstallationWhen transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the UnitFirmly pull both hose holders off the unit Close off the hole with the plug cap GSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Delivery Heads over 1m Technical DataDimensions Measurements in mmCustomer services BelgiumIndex Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG