AEG 82730 manual Head 1m from units floor

Page 35

 

 

 

Instructions for use

 

 

 

 

 

 

Problem

Possible Cause

Remedy

 

 

 

Drainage hose bent.

Remove the bend.

 

 

 

 

Consult Customer Service.

 

 

 

Maximum pump head (outlet

They can supply a retrofit kit

 

 

Washing not well spun.

head 1m from unit's floor

as a special accessory for de-

 

 

Residual water still vis-

surface) exceeded.

livery heads of more than

 

 

ible in the drum.

 

1m.

 

 

Fault code (2 ap-

 

Switch off the unit and pull

 

 

pears.

 

 

 

Solution pump blocked.

out the mains plug. Clean

 

 

 

 

the solution pump.

 

 

 

If a siphon is connected: Si-

Clean the siphon.

 

 

 

phon blocked.

 

 

 

 

 

 

 

Door locked for safety rea-

Wait until the display DOOR/

 

 

 

sons (display DOOR/LIGHT,

 

 

 

LIGHT (DEUR/LICHT, PORTE/

 

 

The filling door cannot

DEUR/LICHT, PORTE/ ECLAIR.

 

 

ECLAIR.) lights up green.

 

 

is off).

 

 

be opened with the

 

 

 

unit switched on.

The program saving function

Cancel the program saving

 

 

 

 

 

 

function (see section ”Pro-

 

 

 

is set.

gram saving”).

 

 

 

 

 

 

Washing detergent res-

Water valve not fully opened.

Open the water valve fully.

 

 

Filter in the screw connec-

Close the water valve. Un-

 

 

idues form in the

 

 

washing detergent

tion of the intake hose on

screw the intake hose from

 

 

drawer.

the water valve or on the

the water valve and from the

 

 

 

unit is blocked.

unit and clean the filter.

 

 

The rinsing water is

The cause is probably a de-

No negative influence on the

 

 

tergent with a high silicate

rinsing result, possibly use

 

 

murky.

 

 

content.

liquid detergent if necessary.

 

 

 

 

 

 

 

 

 

 

The corresponding dis-

 

 

 

 

play does not light up

The selected additional pro-

 

 

 

when one of the addi-

gram cannot be combined

Make another selection.

 

 

tional program but-

with the set program.

 

 

 

tons is pressed.

 

 

 

 

 

Program saving function

 

 

 

The program sequence

switched on; The program

Turn the program selector

 

 

indicator flashes con-

selector was accidentally re-

back to its original position

 

 

stantly.

adjusted during the washing

(see ”Program saving”).

 

 

 

cycle.

 

 

 

 

 

 

 

 

 

 

 

 

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
ÖKO-LAVAMAT 82730 update Dear customer Contents What to do if Solution CoolingPage Correct Use SafetyBefore Putting into Operation for the First Time General Safety Child SafetyFor polyoxymethylene, e.g. plastic clips DisposalEnvironment Tips Dispose the packing materialDrawer for Washing Powder and Care Agent Unit DescriptionFront View Program Selector Control PanelSilk ZIJDE, SOIE/ P Handwash Program Wool WOL, LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean?Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes Water Softener How much washing detergent and care agent?After the Washing Program Ends Run a Washing CycleBrief Instructions Set the Washing ProgramPer minute Change Spin Speed / Select Rinse HoldIf necessary, change the spin speed for the final RevolutionsRed The door is open Set the Delay TimerOpening and Closing the Filling Door OffFor information on the correct preparation of the washing Add the WashingOr for water softener If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentIf the time preselection is set Start the Washing ProgramWashing Cycle Ended/Remove Washing Completion of the Washing ProgramLights up, too much washing detergent was used Washing Program TablesDelicates Soaking Separate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing Drum Before cleaning the drain pump Cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washingCarry Out an Emergency Emptying Operation Gency unlocking and remove the plug from the mains When all the washing solution has drained offEmergency Unlocking of the Filling Door Aid of the emergency unlocking facilitySet Additional Rinse No additional rinse is set when the unit is deliveredAdditional Rinse RINSE+ To rinse with more waterSet the Solution Cooling Solution CoolingCancel Additional Rinse Cancel the Solution Cooling Additional Rinse and Solution CoolingProgram Saving Setting the Program Saving FunctionCanceling the Program Saving Function Cancelling the Child Safety Feature Child Safety FeatureSetting the Child Safety FeatureSafety Instructions for Installation Setting up and connection instructionsTransporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolleyClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Measurements in mm Technical DataDimensions Delivery Heads over 1mBelgium Customer servicesIndex When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG
Top Page Image Contents