AEG 82730 manual Setting Up the Unit, Transporting the Unit, Remove the Transport Safeguard, Tures

Page 45

Setting up and connection instructions

Setting Up the Unit

3	Washing machines with curved panels are not suitable for substruc-
	tures.

Transporting the Unit

•Do not place the washing machine on its front side or on its right side (looking from the front). Otherwise the electrical components can get wet.

•Never transport the unit without using the transport safeguard. Do not remove the transport safeguard until you reach the installation site. Transporting the unit without the transport safeguard can result in damage to the unit.

•Never lift the unit by the open filling door or by its base.

When transporting the unit with a sack trolley:

•Attach the sack trolley only at the side. The scoop of the sack trolley must not be longer than 24cm, otherwise the float switch can be de- stroyed.

Remove the Transport Safeguard

Attention! It is essential to re- move the transport safeguard be- fore putting the unit into operation! Keep all parts of the transport safeguard in a safe place for possible later transport (moving house).

0 1. Open both hose holders on the rear of the unit and remove the hoses and the mains cable.

45

Image 45

Contents

ÖKO-LAVAMAT 82730 update Dear customer Contents What to do if Solution CoolingPage Safety Before Putting into Operation for the First TimeCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsUnit Description Front ViewDrawer for Washing Powder and Care Agent Program Selector Control PanelSilk ZIJDE, SOIE/ P Handwash Program Wool WOL, LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements What Does Update Mean? Water Protection Aqua Control + Aqua AlarmRunning Time Display Before the First Wash Prepare the Washing CycleSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Brief Instructions Run a Washing CycleSet the Washing Program After the Washing Program EndsIf necessary, change the spin speed for the final Change Spin Speed / Select Rinse HoldRevolutions Per minuteOpening and Closing the Filling Door Set the Delay TimerOff Red The door is openFor information on the correct preparation of the washing Add the WashingAdd Washing Detergent/Care Agent If using Liquid Detergent/TabsCompartment for pre-wash agent/soaking agent Or for water softenerIf the time preselection is set Start the Washing ProgramWashing Cycle Ended/Remove Washing Completion of the Washing ProgramLights up, too much washing detergent was used Washing Program TablesDelicates Soaking Separate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpRemedying Faults After remedying the fault, press the buttonWhat to do if Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAid of the emergency unlocking facility Gency unlocking and remove the plug from the mainsAdditional Rinse RINSE+ No additional rinse is set when the unit is deliveredTo rinse with more water Set Additional RinseSolution Cooling Cancel Additional RinseSet the Solution Cooling Cancel the Solution Cooling Additional Rinse and Solution CoolingSetting the Program Saving Function Canceling the Program Saving FunctionProgram Saving Setting the Child Safety Child Safety FeatureFeature Cancelling the Child Safety FeatureSafety Instructions for Installation Setting up and connection instructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitClose off the hole with the plug cap G Firmly pull both hose holders off the unitPrepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Measurements in mmBelgium Customer servicesIndex When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG