AEG 82730 manual Prepare the Installation Location, Setting Up on a Concrete Pedestal

Page 47

Setting up and connection instructions

Prepare the Installation Location

•The installation surface must be clean, dry and free of floor wax resi- due and other lubricating coatings so that the unit does not slide away. Do not use any lubricants as sliding aids.

•It is not recommended to set up the washing machine on deep-pile carpets or on floor coverings with soft foam underlays, as this would mean that the stability of the unit would not be guaranteed.

•Use ordinary rubber mats as underlays in locations with small-format tiles.

•Never use wood, card or similar underlays to compensate for minor floor unevenness. Always use the adjustable screw-type feet of the machine.

•If, for reasons of space, it is not possible to avoid setting up the unit next to a gas cooker or coal stove: Insert a thermally-insulating panel between the washing machine and the cooker (85 x 57cm). This panel must have an aluminium foil on the side against the cooker.

•The washing machine must not be set up in a room where there

is a danger of frost. Frost damage!

•The intake and drainage hoses must not be bent or pinched.

Setting Up on a Concrete Pedestal

When setting up the washing machine on a concrete pedestal, it is essential for safety reasons to fit stand plates in which the washing machine is then adjusted. The stand plates are available from the Customer Service under spare part number 645 425 058.

Setting Up on a Vibrating floor

In the case of vibrating floors, especially wooden beam floors with flex- ible boards, securely screw a water-resistant wooden panel at least 15mm thick onto at least 2 of the floor beams. If possible, set up the unit in a corner of the room where the wooden floor is best firmly in- stalled and is therefore least likely to be susceptible to vibrations.

47

Image 47

Contents

ÖKO-LAVAMAT 82730 update Dear customer Contents What to do if Solution CoolingPage Correct Use SafetyBefore Putting into Operation for the First Time General Safety Child SafetyFor polyoxymethylene, e.g. plastic clips DisposalEnvironment Tips Dispose the packing materialDrawer for Washing Powder and Care Agent Unit DescriptionFront View Program Selector Control PanelSilk ZIJDE, SOIE/ P Handwash Program Wool WOL, LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean?Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes Water Softener How much washing detergent and care agent?After the Washing Program Ends Run a Washing CycleBrief Instructions Set the Washing ProgramPer minute Change Spin Speed / Select Rinse HoldIf necessary, change the spin speed for the final RevolutionsRed The door is open Set the Delay TimerOpening and Closing the Filling Door OffFor information on the correct preparation of the washing Add the WashingOr for water softener If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentIf the time preselection is set Start the Washing ProgramWashing Cycle Ended/Remove Washing Completion of the Washing ProgramLights up, too much washing detergent was used Washing Program TablesDelicates Soaking Separate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washingCarry Out an Emergency Emptying Operation Gency unlocking and remove the plug from the mains When all the washing solution has drained offEmergency Unlocking of the Filling Door Aid of the emergency unlocking facilitySet Additional Rinse No additional rinse is set when the unit is deliveredAdditional Rinse RINSE+ To rinse with more waterSet the Solution Cooling Solution CoolingCancel Additional Rinse Cancel the Solution Cooling Additional Rinse and Solution CoolingProgram Saving Setting the Program Saving FunctionCanceling the Program Saving Function Cancelling the Child Safety Feature Child Safety Feature Setting the Child Safety FeatureSafety Instructions for Installation Setting up and connection instructionsTransporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolleyClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Measurements in mm Technical DataDimensions Delivery Heads over 1mBelgium Customer servicesIndex When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG