AEG 82730 manual Start the Washing Program, If the time preselection is set

Page 23

Instructions for use

Start the Washing Program

01. Check that the water valve is open.

2.Start the washing program: Press the button

START/PAUSE (START/PAUZE, MARCHE/PAUSE). The washing program is started or it starts after the set time expires.

3	If the indicator DOOR/LIGHT (DEUR/LICHT, PORTE/ECLAIR.) lights up red
	when the button START/PAUSE (START/PAUZE, MARCHE/PAUSE) is

pressed, the filling door is not correctly closed. Press the filling door firmly closed and press the button START/PAUSE (START/PAUZE, MARCHE/PAUSE) again.

If the time preselection is set:

The set time preselection runs and the remaining time until the pro- gram start is shown in the multi-display (in full hours in each case). During this time you can load washing or change / abort the time preselection.

• Load washing: Press the button START/PAUSE (START/PAUZE, MARCHE/ PAUSE). The filling door can be opened. Next, close the door and again press the button START/PAUSE (START/PAUZE, MARCHE/PAUSE).

• Change or abort time preselection: Press the button DELAY TIMER (STARTTIJDKEUZE, DEPART DIFFERE) as often as necessary until the re- quired time is displayed; When the program run time is displayed (shown in minutes, e.g.125), the washing program starts without de- lay.

23

Image 23

Contents

ÖKO-LAVAMAT 82730 update Dear customer Contents What to do if Solution CoolingPage Correct Use SafetyBefore Putting into Operation for the First Time General Safety Child SafetyFor polyoxymethylene, e.g. plastic clips DisposalEnvironment Tips Dispose the packing materialDrawer for Washing Powder and Care Agent Unit DescriptionFront View Program Selector Control PanelSilk ZIJDE, SOIE/ P Handwash Program Wool WOL, LAINE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean?Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes Water Softener How much washing detergent and care agent?After the Washing Program Ends Run a Washing CycleBrief Instructions Set the Washing Program Per minute Change Spin Speed / Select Rinse Hold If necessary, change the spin speed for the final RevolutionsRed The door is open Set the Delay TimerOpening and Closing the Filling Door OffFor information on the correct preparation of the washing Add the WashingOr for water softener If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentIf the time preselection is set Start the Washing ProgramWashing Cycle Ended/Remove Washing Completion of the Washing ProgramLights up, too much washing detergent was used Washing Program TablesDelicates Soaking Separate Spin Separate Conditioning/Starching/ImpregnatingWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washingCarry Out an Emergency Emptying Operation Gency unlocking and remove the plug from the mains When all the washing solution has drained offEmergency Unlocking of the Filling Door Aid of the emergency unlocking facilitySet Additional Rinse No additional rinse is set when the unit is deliveredAdditional Rinse RINSE+ To rinse with more waterSet the Solution Cooling Solution CoolingCancel Additional Rinse Cancel the Solution Cooling Additional Rinse and Solution CoolingProgram Saving Setting the Program Saving FunctionCanceling the Program Saving Function Cancelling the Child Safety Feature Child Safety FeatureSetting the Child Safety FeatureSafety Instructions for Installation Setting up and connection instructionsTransporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolleyClose off the hole with the plug cap G Firmly pull both hose holders off the unitSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Measurements in mm Technical DataDimensions Delivery Heads over 1mBelgium Customer servicesIndex When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG