AEG 82730 Set the Delay Timer, Opening and Closing the Filling Door, Off, Red The door is open

Page 20

Instructions for use

Set the Delay Timer

0 Set the delay timer if necessary: Press the button DELAY TIMER (STARTTIJD- KEUZE, DEPART DIFFERE) as often as neces-

sary until the required start delay is shown in the multi-display, for example in the form

12h for a program start delay 12 hours.

If19h is displayed and you press again, the run time of the set washing program (display in minutes, e. g.125) appears. In this state, the delay timer is not set.

If the button SOAKING (INWEKEN, TREMPAGE) is pressed, the delay timer determines the soaking time. (Without timer delay, the soaking time is approx. 1 hour.)

Opening and Closing the Filling Door

0Open: Press the button DOOR/LIGHT (DEUR/LI-

CHT, PORTE/ECLAIR.). The filling door springs open.

0Close: Press the filling door firmly closed.

When the unit is switched on, the display DOOR/LIGHT (DEUR/LICHT, PORTE/ECLAIR.) shows whether the filling door can be opened:

–green: The door can be opened (not when the program saving func- tion is activated, for details see the section ”Program Saving”)

– off:

The door cannot be opened at present

–red: The door is open

3	The washing drum is illuminated when the filling door is open. The light
	goes out automatically after approx. 3 minutes.

20

Image 20

Contents

ÖKO-LAVAMAT 82730 update Dear customer Contents Solution Cooling What to do ifPage Correct Use SafetyBefore Putting into Operation for the First Time Child Safety General SafetyDisposal Environment TipsDispose the packing material For polyoxymethylene, e.g. plastic clipsDrawer for Washing Powder and Care Agent Unit DescriptionFront View Control Panel Program SelectorWool WOL, LAINE/ P Handwash Program Silk ZIJDE, SOIE/ P Handwash ProgramAdditional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean?Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes How much washing detergent and care agent? Water SoftenerRun a Washing Cycle Brief InstructionsSet the Washing Program After the Washing Program EndsChange Spin Speed / Select Rinse Hold If necessary, change the spin speed for the finalRevolutions Per minuteSet the Delay Timer Opening and Closing the Filling DoorOff Red The door is openAdd the Washing For information on the correct preparation of the washingIf using Liquid Detergent/Tabs Add Washing Detergent/Care AgentCompartment for pre-wash agent/soaking agent Or for water softenerStart the Washing Program If the time preselection is setCompletion of the Washing Program Washing Cycle Ended/Remove WashingLights up, too much washing detergent was used Program Tables WashingDelicates Soaking Separate Conditioning/Starching/Impregnating Separate SpinCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Ter valve, remove the filter Fault code 1 ap Tighten the intake hose Head 1m from units floor If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAid of the emergency unlocking facility Gency unlocking and remove the plug from the mainsNo additional rinse is set when the unit is delivered Additional Rinse RINSE+To rinse with more water Set Additional RinseSet the Solution Cooling Solution CoolingCancel Additional Rinse Additional Rinse and Solution Cooling Cancel the Solution CoolingProgram Saving Setting the Program Saving FunctionCanceling the Program Saving Function Child Safety Feature Setting the Child SafetyFeature Cancelling the Child Safety FeatureSetting up and connection instructions Safety Instructions for InstallationSetting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the UnitFirmly pull both hose holders off the unit Close off the hole with the plug cap GSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Technical Data DimensionsDelivery Heads over 1m Measurements in mmCustomer services BelgiumIndex Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG