AEG 70730 manual Prepare the Installation Location, Setting Up on a Concrete Pedestal

Page 46

Setting up and connection instructions

Prepare the Installation Location

•The installation surface must be clean, dry and free of floor wax resi- due and other lubricating coatings so that the unit does not slide away. Do not use any lubricants as sliding aids.

•It is not recommended to set up the washing machine on deep-pile carpets or on floor coverings with soft foam underlays, as this would mean that the stability of the unit would not be guaranteed.

•Use ordinary rubber mats as underlays in locations with small-format tiles.

•Never use wood, card or similar underlays to compensate for minor floor unevenness. Always use the adjustable screw-type feet of the machine.

•If, for reasons of space, it is not possible to avoid setting up the unit next to a gas cooker or coal stove: Insert a thermally-insulating panel between the washing machine and the cooker (85 x 57cm). This panel must have an aluminium foil on the side against the cooker.

•The washing machine must not be set up in a room where there

is a danger of frost. Frost damage!

•The intake and drainage hoses must not be bent or pinched.

Setting Up on a Concrete Pedestal

When setting up the washing machine on a concrete pedestal, it is essential for safety reasons to fit stand plates in which the washing machine is then adjusted. The stand plates are available from the Customer Service under spare part number 645 425 058.

Setting Up on a Vibrating floor

In the case of vibrating floors, especially wooden beam floors with flex- ible boards, securely screw a water-resistant wooden panel at least 15mm thick onto at least 2 of the floor beams. If possible, set up the unit in a corner of the room where the wooden floor is best firmly installed and is therefore least likely to be susceptible to vibrations.

46

Image 46

Contents ÖKO-LAVAMAT 70730 update Dear customer Tel /3630444Contents Remedying Faults What to do ifContents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironment Tips Dispose the old applianceFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control Panel Program SelectorEASY-CARES KREUKHERSTELLEND, Defroissable Woollens WOL, LAINE/P HandwashAdditional Program Buttons PRE Wash VOORWAS, PrelavConsumption Values and Time Requirements What Does Update Mean? Water Protection Aqua ControlPrepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent?Water Hardness Details Brief Instructions Run a Washing CycleAfter the Washing Program Ends Set the Washing Program Set the Delay Timer/Soaking Duration Change Spin Speed / Select Rinse HoldSoaking Duration This run time is comprised as followsOpening and Closing the Filling Door Add the WashingCompartment for pre-wash agent/soaking agent If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Or for water softenerStart the Washing Program If the time preselection is setProgram Sequence Display Completion of the Washing ProgramChanging a Washing Program Multi-DisplaySelect the Additional Program Change the Spin SpeedWashing Cycle Ended/Remove Washing Program Tables WashingEASY-CARES PRE Wash Separate Rinse Separate Conditioning/Starching/ImpregnatingSeparate Spin Cleaning and Care Washing Detergent DrawerWashing Drum Filling DoorRemedying Faults What to do ifRINCAGE+ flashes Water Sans Repassage Washing detergent If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Clean the Solution Pump When all the washing solution has drained offEmergency Unlocking of the Filling Door Additional Rinse RINSE+/SPOELEN+/RINCAGE+ Cancel Additional RinseSet Additional Rinse Setting the Child Safety Feature Child Safety FeatureCancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for InstallationWhen transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the UnitFirmly pull both hose holders off the unit Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Page Page Index Service When do you incur costs even during the warranty period?