Fisher & Paykel Fisher and Paykel AquaSmart Washing Machine Manual: Reset and Out-of-Balance Solutions

Page 25

Changing pre-set options

23

Out-of-Balance recovery routine

When your AquaSmart™ is spinning it can sense if the wash load is out-of-balance and will stop and re-try spinning up to 3 times. If it still senses an unbalanced load there are two options the machine can take.

Automatic Recovery option

Your AquaSmart™ will try to automatically correct the out-of-balance load. It will fill with water and agitate to redistribute the load before trying to spin up again.

Machine Stops option

Your AquaSmart™ will stop, give a short burst of beeps every 5 seconds, and the spin speed lights will flash. You must redistribute the load more evenly yourself. (Use this option if you wish to conserve water).

Your washer arrived with the ‘Machine Stops’ option set.

1Enter Options Adjustment mode (refer to page 20).

2Select SOAK to program your AquaSmart™ to automatically recover.

3Press POWER to save your selection.

SOAK

light on = automatic recovery

SOAK

light off = machine stops

Fig.17 Adjusting Out-of-Balance recovery routine

 

Reset Back to Factory Settings

 

 

If you would like to reset all settings back to those that

 

 

were set when your AquaSmart™ left the factory you have

 

 

the option of selecting RESET DEFAULTS.

 

1

Enter Option Adjust Mode (refer to page 20).

 

2

Press and hold the START /PAUSE button until you hear

 

 

one quick beep. This indicates that all settings have been

Fig.18 Resetting factory defaults

 

returned to the factory default settings.

 

 

Image 25
Contents Installation instructions and user guide Contents Welcome to AquaSmart IntroductionInstallation  Installation instructionsUnpacking Drain hoseWater supply Installation instructionsInlet hoses ElectricalAccessories and spare parts Clothes washer safetyLevelling your machine AquaSmart water consumption Before you do your first washAquaSmart capacity Detergent Getting started quicklyGetting started quickly Conventional mode High Efficiency modeUnique AquaSmart wash Detergent Activating washFully automatic water level Sorting and loadingSorting and loading Loading SortingDetergent Where do I put my detergent?Choosing the right detergent How much detergent?Fabric softener Cleaning the dispenserChoosing the right cycle Adding the fabric softenerWash cycles explained Regular Changing the wash cycle optionsHeavy DelicateColours Wash cycles explained SheetsEasy Iron Wash cycles explainedWash cycle options explained Soak Delay StartWash Advance Lid lock Auto drainTo unlock the lid at any time press START/PAUSE To customise a cycle Customising the wash cyclesTo enter Option Adjustment mode Option Adjustment modeChanging pre-set options Controlled Cold Wash temperaturesEnd of Cycle beeps Aqua RinseReset Back to Factory Settings Out-of-Balance recovery routineAutomatic Recovery option Machine Stops optionControl Panel Lighting Cleaning your AquaSmart When you have finished the cycleCleaning the soft touch buttons and topdeck Cleaning the inside of your washerAutomatic lint disposal system Cleaning your low profile agitatorNappy sanitisers/bleach ABC washing guide Hottest setting in the dryer that the fabric will handle Drying. Advance cycle to Spin using the Advance buttonDamp Items Duvet/Doona InnersLingerie Colour lossNappies Sensitive SkinSuch as table cloths. Choose Sheets cycle TableclothsTea Towels Throws Choose Bulky cycle TowelsHOT water temperature light is flashing HOT and Cold water temperature lights are both flashingMusical series of beeps every 5 seconds and… Spin Speed and the Rinse or Spin light is flashingBefore you call for service Solving operating problems Small amount of Water in Bowl AT END of Cycle Wash Cycle Time longer than usualBlack or Gray Marks on Clothes Solving wash problemsThis warranty does not cover Manufacturer’s warrantyFisher & Paykel undertakes to New Zealand if you need assistance Customer careAustralia if you need assistance Product details Model/Serial NoNZ AU