Fisher & Paykel WL80T65D Installation instructions, Water supply, Inlet hoses, Electrical

Page 5

Installation instructions

Water supply

This clothes washer should be plumbed into both a hot and cold water supply otherwise some cycles may not function correctly.

For best operating conditions your hot water should be approximately 65˚C. Your hot water should not exceed 75˚C or your cold water exceed 35˚C. Temperatures above these may cause a fault or cause damage to the machine.

If you have an uncontrolled water-heating source (eg. a wet back or solar heating) you should have a tempering device fitted. This will ensure the hot water temperature remains within safe limits. For the most suitable type of tempering device we recommend you contact a local plumber or plumbing supply merchant.

Inlet Water Static Pressure of between 3psi (20kPa) and 150psi (1MPa) is recommended.

(If using a header tank then the top of the header tank must be at least 2 metres above the top of your clothes washer).

Minimum flow rate from the tap supplying the clothes washer should be greater than 6 litres/min (assumes 12.7mm (1/2 inch) diameter pipes).

Minimum height of taps to clear the top of the machine is 1150 mm.

Inlet hoses

1Connect the straight ends of the white inlet hoses to the taps (there are washers fitted in both ends).

2Connect the elbow ends of the white inlet hoses to the machine inlet valves. Inlet valves are marked on the back of the machine.

H=HotC=Cold

Tap end

Machine end

Fig.3 Inlet hose ends

Electrical

This appliance must be supplied with a 230V - 240V, 50Hz, sinusoidal, 450W electrical supply.

Image 5

Contents Installation instructions and user guide Contents Welcome to AquaSmart IntroductionInstallation Installation instructionsUnpacking Drain hoseWater supply Installation instructionsInlet hoses ElectricalLevelling your machine Clothes washer safetyAccessories and spare parts AquaSmart capacity Before you do your first washAquaSmart water consumption Detergent Getting started quicklyGetting started quickly Conventional mode High Efficiency modeUnique AquaSmart wash Detergent Activating washSorting and loading Sorting and loadingFully automatic water level Loading SortingDetergent Where do I put my detergent?Choosing the right detergent How much detergent?Fabric softener Cleaning the dispenserChoosing the right cycle Adding the fabric softenerWash cycles explained Regular Changing the wash cycle optionsHeavy DelicateColours Wash cycles explained SheetsEasy Iron Wash cycles explainedWash cycle options explained Wash Advance Delay StartSoak To unlock the lid at any time press START/PAUSE Auto drainLid lock To customise a cycle Customising the wash cyclesChanging pre-set options Option Adjustment modeTo enter Option Adjustment mode Controlled Cold Wash temperaturesEnd of Cycle beeps Aqua RinseReset Back to Factory Settings Out-of-Balance recovery routineAutomatic Recovery option Machine Stops optionControl Panel Lighting Cleaning your AquaSmart When you have finished the cycleCleaning the soft touch buttons and topdeck Cleaning the inside of your washerNappy sanitisers/bleach Cleaning your low profile agitatorAutomatic lint disposal system ABC washing guide Hottest setting in the dryer that the fabric will handle Drying. Advance cycle to Spin using the Advance buttonDamp Items Duvet/Doona InnersLingerie Colour lossNappies Sensitive SkinSuch as table cloths. Choose Sheets cycle TableclothsTea Towels Throws Choose Bulky cycle TowelsHOT water temperature light is flashing HOT and Cold water temperature lights are both flashingMusical series of beeps every 5 seconds and… Spin Speed and the Rinse or Spin light is flashingBefore you call for service Solving operating problems Small amount of Water in Bowl AT END of Cycle Wash Cycle Time longer than usualBlack or Gray Marks on Clothes Solving wash problemsFisher & Paykel undertakes to Manufacturer’s warrantyThis warranty does not cover New Zealand if you need assistance Customer careAustralia if you need assistance Product details Model/Serial NoNZ AU