Bosch Appliances WAP24201UC manual Default cycle settings, Additional program settings

Page 21

Default cycle settings

At the factory, a temperature range, spin speed range, and cycle duration ("Finish at" time) are pre-set for all cycles.

After selection of the cycle, these values are displayed in the display field.

You can change the default settings as follows.

Changing the temperature range

Before and during the cycle, you can change the default temperature range depending on the cycle progress. Press the appropriate button until the desired setting is displayed.

The maximum temperature range that can be set depends on the cycle selected.

~Cycle selection table; Page 19

Changing the spin speed range

Before and during the cycle, you can change the spin speed range depending on the cycle progress.

Press the appropriate button until the desired setting is displayed.

No spin setting: Rinse stop = without final spin, the laundry remains in the last rinse water.

The maximum speed range that can be set depends on the cycle selected.

~Cycle selection table; Page 19

Delay Start

When you select a cycle, the duration of the cycle in question is displayed.

Before the cycle start, the cycle end ("Finish at" time) can be pre-selected in one-hour steps (h=hour) up to a maximum of 24h.

Press the Delay Start button until the desired setting is displayed.

NOTICE: The cycle duration is included in the set "Finish at" time.

After the start, the pre-selected time, e.g. 8h is displayed and counted down until the wash cycle begins. Then the cycle duration, e.g. 2:40 (hours:minutes) is displayed.

Changing the pre-selected time:

If the “Delay Start” function has been activated and before the wash cycle has started, you can change the delay time as follows:

1.Press Start/Pause.

2.Press the Delay Start button until the desired number of hours is displayed.

3.Press the Start/Pause button

NOTICE: The cycle duration is adjusted automatically when the cycle is running. Changes to the default cycle settings or cycle settings also cause changes in the cycle duration.

Additional program settings

Extra Rinse

Auxillary rinse cycle. Longer cycle duration. For areas with very soft water or for further improvement of rinse results.

Easy Iron

Special spin cycle with final loosening up of laundry. Delicate final spin - moisture remaining in the laundry is slightly increased.

Prewash/Pre Treat

For heavily soiled washing. Pour detergent into dispensers I and II.

21

Image 21
Contents Washer Welcome to Your New Washer Table of contents ~ Troubleshooting Customer serviceImportant information Purchase informationYour washing machine is intended for Importance and meaning of symbols~ Electrical connection Important Safety InstructionsSpecial features Standard features and helpful informationIntroduction to your new washer Length of power cord and water supply hoses Dimensions and clearances requiredInstallation types Appliance dimensionsMinimum opening dimensions Vent spacing actual not minimum dimensionsClearance requirements Minimum Ventilation area MinimumTools needed Installation instructionsIntroduction Waste disposalInstallation checklist Set up on a pedestal with drawerImportance of installing on a solid, level Parts provided with your washerWater connections Remove the transport boltsDamage to the Appliance Water supply hose connectionsWater drain hose connection Height of drain pointTypes of drainage hookups Standpipe Electrical connection Leveling the washerTransporting the washer Getting to know your appliance Temp. selection, Spin Speed, Delay-StartDisplay field Control panelSorting the Laundry LaundryIdentifying and treating stains Preparing the laundryAdding the correct amount of HE detergent Laundry detergents and additivesCycle selection table Starching Dyeing/bleachingSoaking Additional program settings Default cycle settingsOperating Instructions Filling the detergent and additives compartments ~ Standard features and helpful informationRecommended Load Size FillingCancel cycle Pausing/Continuing the cycleRemoving laundry/switching the appliance off Starting the cycleActivate adjustment mode for the signal volume SignalSetting volume for button signals depending on the model Setting volume for indicator signalsCleaning and maintenance Clean the strainers at the water tap end of the hose Cleaning the drain pumpClean the strainers at the washer end of the hose Risk of ScaldingPage Troubleshooting Troubleshooting~ Cleaning the drain pump Emergency door lock releaseDeterming the Problem Problem Possible causes Solutions~ Emergency door lock release ~ Remove the transport bolts Error messages Customer serviceDisplay MeasureBosch Clothes Washer Statement of Limited Product WarrantyScope of Warranty Page 9000826642