Bosch Appliances WAP24201UC manual Starting the cycle, Child lock, Selecting a different cycle

Page 24

Liquid detergent dispenser

To measure liquid detergent:

1.Pull out the detergent drawer. Press down on the insert and remove the drawer completely.

2.Push the liquid detergent dispenser forward.

3.Insert the drawer again.

NOTICE: Do not use the liquid detergent dispenser with gel-type detergents and powdered detergents or for cycles with pre-wash and selected "Finish at" time.

Starting the cycle

Press the Start/Pause button Indicator lamp lights up and the cycle starts.

NOTICE: If you want to protect the cycle against inadvertent adjustment, select the child lock.

~Child lock; Page 24

During the cycle, the display field indicates the "Finish at" time and, after starting the washing cycle, the cycle duration and the symbols for the cycle progress.

~Display field; Page 16

Child lock

You can secure the washer against inadvertent changing of the set functions. To do this, activate the child lock after cycle start.

To Activate/Deactivate, press Start/Pause for approx. 5 seconds. In the display field, you will see the D symbol.

▯D lit steady: The child lock is active.

▯D blinking: The child lock is active and the cycle selector has been adjusted. To prevent a cycle interruption, set the cycle selector back to the initial cycle. The symbol lights up again.

NOTICE: The child lock can remain activated until the next cycle start even after switching the machine off. Then you must deactivate the child lock before cycle start and if necessary activate it again after cycle start.

Selecting a different cycle

If you have inadvertently started the wrong cycle, you can change this as follows:

1.Press Start/Pause.

2.Select another cycle.

3.Press Start/Pause. The new cycle starts from the beginning.

Pausing/Continuing the cycle

e.g. for soaking ~ Soaking; Page 20

Press Start/Pause. - ¿ - appears on the display panel; washing machine door cannot be opened. To continue the cycle, press Start/Pause.

Cancel cycle

For cycles with a high temperature:

1.Press Start/Pause.

2.Cool the laundry off: Select Rinse.

3.Press Start/Pause.

For cycles with a low temperature:

1.Press Start/Pause.

2.Select Spin/Drain.

3.Press Start/Pause.

Cycle end with rinse stop

Appears in the display field – – – and the indicator lamp on the Start/Pause button blinks.

In order to exit the cycle, set the cycle selector to Spin/ Drain or select a spin speed range, then press the Start/ Pause button.

Cycle end

End appears in the display field and the Start/Pause button indicator lamp is off.

If the cycle status sequence Wash is also flashing in the display field, the washer has detected too much foam during the washing cycle and it has then automatically switched on a rinse to remove the foam.

NOTICE: Use less detergent the next time you run the washer with the same load.

Removing laundry/switching the appliance off

1.Open the front door of the washer and remove the laundry.

2.Turn the cycle selector to the Off position. Appliance is switched off.

3.Turn off the water tap.

NOTICES

▯Do not leave any laundry in the drum. It can shrink or be discolored by the next laundry.

▯Remove any remaining items from the drum and rubber gasket.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Washer Welcome to Your New Washer Table of contents Customer service ~ TroubleshootingImportant information Purchase informationImportance and meaning of symbols Your washing machine is intended forImportant Safety Instructions ~ Electrical connectionSpecial features Standard features and helpful informationIntroduction to your new washer Dimensions and clearances required Length of power cord and water supply hosesInstallation types Appliance dimensionsVent spacing actual not minimum dimensions Minimum opening dimensionsClearance requirements Minimum Ventilation area MinimumInstallation instructions Tools neededIntroduction Waste disposalSet up on a pedestal with drawer Installation checklistImportance of installing on a solid, level Parts provided with your washerRemove the transport bolts Water connectionsDamage to the Appliance Water supply hose connectionsWater drain hose connection Height of drain pointTypes of drainage hookups Standpipe Leveling the washer Electrical connectionTransporting the washer Temp. selection, Spin Speed, Delay-Start Getting to know your applianceDisplay field Control panelLaundry Sorting the LaundryIdentifying and treating stains Preparing the laundryLaundry detergents and additives Adding the correct amount of HE detergentCycle selection table Starching Dyeing/bleachingSoaking Default cycle settings Additional program settingsOperating Instructions ~ Standard features and helpful information Filling the detergent and additives compartmentsRecommended Load Size FillingPausing/Continuing the cycle Cancel cycleRemoving laundry/switching the appliance off Starting the cycleSignal Activate adjustment mode for the signal volumeSetting volume for button signals depending on the model Setting volume for indicator signalsCleaning and maintenance Cleaning the drain pump Clean the strainers at the water tap end of the hoseClean the strainers at the washer end of the hose Risk of ScaldingPage Troubleshooting Troubleshooting~ Cleaning the drain pump Emergency door lock releaseDeterming the Problem Problem Possible causes Solutions~ Emergency door lock release ~ Remove the transport bolts Customer service Error messagesDisplay MeasureStatement of Limited Product Warranty Bosch Clothes WasherScope of Warranty Page 9000826642
Top Page Image Contents