Electrolux EWW 168543 W user manual Positioning, Water Inlet, Rubber Feet KIT

Page 27

6.Fill the smaller upper hole and the two large ones with the corresponding plas- tic plug caps supplied in the bag con- taining the instruction booklet.

POSITIONING

Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable. If nec- essary, check the setting with a spirit level. Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation.

Caution! Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

electrolux 27

The rubber feet are particularly recommen- ded on floating, slippery and wooden floors. Mount the rubber feet to prevent vibration, noises and displacement of the appliance during operation.

Read carefully the instructions supplied with the kit.

WATER INLET

Warning! This appliance must be connected to a cold water supply.

1.Connect the water inlet hose supplied with the machine to a tap with a 3/4" thread. Always use the hose supplied with the appliance.

Important! Do not use the hose from your previous machine to connect to the water supply.

2.The other end of the inlet hose which connects to the machine can be turned as showed in the picture.

Do not place the inlet hose downwards. Angle the hose to the left or right de- pending on the position of your water tap.

RUBBER FEET KIT (4055126249)

Available from your authorized dealer.

45° 35°

3.Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.

The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new,

Image 27
Contents EN Washer Dryer Safety Information ContentsInstallation Child SafetyUSE Product Description Detergent Dispenser Drawer Control PanelSpin Reduction TemperatureDelay Start Programme Selector DialDelay Time value Child safety lock see «PersonaliDelay icon Alarm codesPersonalisation Acoustic SignalsChild Safety Lock First USEReduce the Spin Speed by Pressing Button Select the Temperature by Pressing ButtonSelect the Delay Start by Pressing Button Cancelling the delayed start after hav- ing pressed buttonAltering AN Option or a Running Programme Cancelling a ProgrammeStart the Programme by Pressing Button Select the Time Manager Option by Pressing ButtonsUSE Drying AT the END of the ProgrammeDrying only USE Washing & Drying NON-STOP Programme Washing and Automatic DryingNON-STOP Programme Washing and Timed Drying Sorting OUT the Laundry TemperaturesHelpful Hints and Tips Fluff in the FabricsDetergents and Additives Laundry WeightsMaximum Loads Removing StainsLaundry not Suitable for Drying Drying HintsDegrees of Water Hardness Preparing the Drying CycleOptions Washing ProgrammesDrying Cycle Duration Additional DryingSpin Seda 30 ColdRinse DrainDrying Programmes Automatic ProgrammesTimed Programmes External Cleaning Care and CleaningCleaning the Dispenser Drawer Descaling Maintenance WashWashing Drum Door SealDrain Pump Cleaning the Water Inlet Filters Frost Precautions What to do IF…Emergency Emptying OUT Possible cause/Solution ProblemToo little detergent or unsuitable detergent has been used Water consumption Technical DataConsumption Values ProgrammeUnpacking InstallationPositioning Water InletRubber Feet KIT Water Drainage Electrical ConnectionEcological Hints Must be carried out by a Service CentreEnvironment Concerns Packaging MaterialsElectrolux Electrolux 132936871-A-502011