AEG 14820 manual Water inlet filter, Emergency emptying out, Frost precautions

Page 36

Cleaning and maintenance

Water inlet filter

If you notice that the machine is taking longer to fill, check that the filter in the water inlet hose is not blocked.

Turn off the water tap.

Unscrew the hose from the tap.

Clean the filter in the hose with a stiff brush.

Screw the hose back onto the tap.

Emergency emptying out

If the water is not discharged, proceed as follows to empty out the machine:

•pull out the plug from the power socket;

•close the water tap;

•if necessary, wait until the water has cooled down;

•open the the pump door;

•place a bowl on the floor and place the end of the emergency emptying hose into the bowl. Remove its cap. The water should drain by gravity into the bowl. Whe the bowl is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water stops flowing out;

•clean the pump if necessary as previously described;

•replace the emergency emptying hose in its seat after having plug- ged it;

•screw the pump again and close the door.

Frost precautions

If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows:

•Close the water tap and unscrew the water inlet hose from the tap.

•Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out.

•Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again.

By doing this, any water remaining in the machine is removed, avoiding ice forming and consequently damage to the appliance.

When you use the machine again, make sure that the ambient temper- ature is above 0°C.

36

Image 36

Contents Lavamat Turbo Dear customer Contents Page Contents Technical data Service Safety instructions General safetyPositioning, connection, starting up Follow the instructions for positioning and connectionChild safety Proper useDisposal Tips for environmental protectionPackaging materials MachineMain features of your washer-dryer Description of the appliance Front viewControl panel Programme selector dialTions Cottons SyntheticsProgramme Option buttons Position at 40C = Easy to ironPosition = drying This function cannot be used withSensitive ProgrammeDelay Start button START/PAUSE buttonElectronic Drying button Drying Time button DisplayProgramme progress display Has finished, the pilot light comes onCancelling a programme Altering an option which is runningOpening the door after the programme has started Detergent dispenser drawer Before the first washPreparing the wash cycle Sorting out and preparing the laundrySort of laundry Approximate Dry weights Types of fabric and care labelsCotton SyntheticsDelicates 40 Detergents and additives Preparing the drying cycle LoadGarments not suitable for drying As a dryer, the machine works on the condensation principleDrying symbols on garment labels Duration of the drying cycleModification of the drying time or degree of drying Fibre residueHow to wash Additional dryingMax. load Load the laundrySelection of the desired wash programme Selection of the desired optionsSelection of the spin speed or option Synthetics 900 r.p.m Delicates WoolSelection of the option Starting the programmeOn the display appears 0’. Press the button again At the end of the programme Automatic washing and drying NON-STOP programmeAdd detergent and additive Select the wash programmeHow to dry Drying only Max. loadProgramme chart Wash programmesSpecial programmes DescripConsumption TionDrying Degree of dryingDrying time Spin speed Mins 1400 Consumption data for drying Max Water Energy Duration Load900 Cleaning and maintenance Periodical cleaning ExteriorAfter each wash Detergent dispenser drawerDoor seal Drain pumpFrost precautions Water inlet filterEmergency emptying out Troubleshooting Problem Possible cause SolutionSomething not working? Problem Possible cause SolutionNoisy Feet have not been Problem Possible cause E10Unsatisfactory washing results If grey stains remain on the laundryFoam is still visible even after the last rinse White residue is left on the laundryTechnical data Water pressure 05-0,8 MPaThis appliance complies with the following EC directives Service Instructions for installation and electrical connection Safety instructions for the installerDimensions of the appliance Front view and side viewRear view Installation UnpackingPositioning LevellingPlug the open Holes with Water inlet Water drainageEnd of the drain hose can be positioned in three ways Electrical connection Permanent connectionConnect the machine to an earthed socket From the Electrolux Group. The world’s No choice