Maytag W10335465B Connecting 3-Wire Connection Power Supply Cord, Standard Power Cord Connectors

Page 25

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Connecting 3-Wire Connection: Power Supply Cord

Standard Power Cord Connectors

2. Connect neutral wire to center terminal block.

Flanged spade connector

Ring Connector

Connecting Neutral Wire

1. Loosen or remove center terminal block screw.

3. Connect remaining wires with outer terminal block screws.

Connecting 4-Wire Connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable,

leaving bare ground wire at 5" (127 mm). Cut 112" (38 mm) from 3 remaining wires. Strip insulation back 1" (25 mm). Shape ends of wires into a hook shape.

Connecting Ground and Neutral Wires

1.Remove center terminal block screw and the ground wire by removing the external ground connector screw.

25

Image 25
Contents Installation Instructions Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Tools Needed Tools & PartsParts Supplied Accessories Alternate Parts and AccessoriesAlternate Parts Dimensions DIMENSIONS/CLEARANCESClearances Stacked Washer/Gas Dryer Location Stacked WASHER/GAS Dryer Installation RequirementsStacked Washer/Gas Dryer Grounding Stacked Washer/Gas Dryer Electrical RequirementsStacked Washer/Gas Dryer Gas Supply Stacked washer/electric dryer installation clearances Stacked WASHER/ELECTRIC Dryer Installation RequirementsStacked Washer/Electric Dryer Location Stacked Washer/Electric Dryer Electrical Requirements If using a power supply cord It is your responsibility Electric Dryer Power Supply CordDryer Electrical Requirements Electrical ConnectionDryer Direct Wire If connecting by direct wire Elbows Dryer Venting RequirementsClamps Rigid metal ventVent System Length Vent HoodsMultiple Dryer Venting If an Exhaust Hood Cannot be UsedType of Gas Dryer GAS Supply RequirementsGas Supply Line Remove Transport System Installing Stacked WASHER/DRYERConnect Inlet Hoses to Washer Connect Inlet HosesConnect Inlet Hoses to Water Faucets Clear Water LinesSecure Drain Hose Route Drain HoseRemove drain hose from the washer drum Laundry tub drain or standpipe drainStandpipe drain system wall or floor Washer Drain SystemWall Laundry tub drain system FloorPower Supply Cord Strain Relief Direct Wire Strain ReliefElectric Dryer Electrical Connections Strain ReliefConnection Options Connecting 4-Wire Connection Power Supply CordConnecting 4-Wire Connection Direct Wire Connecting 3-Wire Connection Power Supply CordStandard Power Cord Connectors Connecting Neutral WireConnecting Remaining Wires Connecting 3-Wire Connection Direct WireLeveling Connecting 3-Wire Connection OptionalLeveling Stacked Washer/Dryer Complete Installation Reversing Dryer Door Swing Remove the Door AssemblyReverse Hinge Reinstall the door Replace the Door AssemblyReverse the strike Cleaning the Door Seal/Bellow To clean washer interior Stacked WASHER/DRYER Maintenance InstructionsMaintenance Instructions WasherDryer If YOU Need AssistanceGeneral Washer/Dryer User Information Electronic Control Setup InstructionsWasher control Dryer controlHow to Use the Buttons to Program the Controls Control Set-up ProceduresThere are four 4 types of dryer pricing Fixed Vend Pricing Accumulator PricingSet-Up Codes Start Operating Set-upExplanation Code ExplanationOptions 3.XX 9.XX to USE if Special Pricing is Selected Code Explanation Value of Coin Special Price Start HourCE Clear Escrow Option Cd Payment Mode COIN/DEBIT OptionMULTI-LOAD Washer and Dryer Warranty