Maytag W10335465B installation instructions Tools & Parts, Tools Needed, Parts Supplied

Page 5

TOOLS & PARTS

Tools Needed:

8" (203 mm)

8" (203 mm) or 10" (254 mm)

flat-blade screwdriver

phillips screwdriver

or 10" (254 mm)

adjustable wrench

 

 

pipe wrench

that opens to 1" (25 mm)

 

 

Torx®† T-20 security

1" (25 mm) hex-head

5⁄16" socket wrench

pliers

screwdriver or bit

socket wrench

 

(that open to 19/16" [39 mm])

level

utility knife

1/4" (6 mm) nut driver

locking pliers

caulk gun and caulk

vent clamps

pipe-joint compound

27" (686 mm) wood block

(for installing new exhaust vent)

 

suitable for gas type

 

flashlight (optional)

1/2" (13 mm) and 9/16"

ruler or measuring tape

 

(14 mm) open-end wrenches

 

Parts Supplied:

water inlet hoses (2)

inlet hose washers (4)

U-shaped hose form

transit bolt hole plug (4)

beaded tie strap

drain hose/clamp

†® TORX is a registered trademark of Saturn Fasteners, Inc.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Installation Instructions Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Parts Supplied Tools & PartsTools Needed Alternate Parts Alternate Parts and AccessoriesAccessories Clearances DIMENSIONS/CLEARANCESDimensions Stacked Washer/Gas Dryer Location Stacked WASHER/GAS Dryer Installation RequirementsStacked Washer/Gas Dryer Grounding Stacked Washer/Gas Dryer Electrical RequirementsStacked Washer/Gas Dryer Gas Supply Stacked Washer/Electric Dryer Location Stacked WASHER/ELECTRIC Dryer Installation RequirementsStacked washer/electric dryer installation clearances Stacked Washer/Electric Dryer Electrical Requirements If using a power supply cord It is your responsibility Electric Dryer Power Supply CordDryer Electrical Requirements Electrical ConnectionDryer Direct Wire If connecting by direct wire Elbows Dryer Venting RequirementsClamps Rigid metal ventVent System Length Vent HoodsMultiple Dryer Venting If an Exhaust Hood Cannot be UsedGas Supply Line Dryer GAS Supply RequirementsType of Gas Remove Transport System Installing Stacked WASHER/DRYERConnect Inlet Hoses to Washer Connect Inlet HosesConnect Inlet Hoses to Water Faucets Clear Water LinesSecure Drain Hose Route Drain HoseRemove drain hose from the washer drum Laundry tub drain or standpipe drainStandpipe drain system wall or floor Washer Drain SystemWall Laundry tub drain system FloorPower Supply Cord Strain Relief Direct Wire Strain ReliefElectric Dryer Electrical Connections Strain ReliefConnection Options Connecting 4-Wire Connection Power Supply CordConnecting 4-Wire Connection Direct Wire Connecting 3-Wire Connection Power Supply CordStandard Power Cord Connectors Connecting Neutral WireConnecting Remaining Wires Connecting 3-Wire Connection Direct WireLeveling Stacked Washer/Dryer Connecting 3-Wire Connection OptionalLeveling Complete Installation Reverse Hinge Remove the Door AssemblyReversing Dryer Door Swing Reverse the strike Replace the Door AssemblyReinstall the door Cleaning the Door Seal/Bellow To clean washer interior Stacked WASHER/DRYER Maintenance InstructionsMaintenance Instructions WasherDryer If YOU Need AssistanceGeneral Washer/Dryer User Information Electronic Control Setup InstructionsWasher control Dryer controlHow to Use the Buttons to Program the Controls Control Set-up ProceduresThere are four 4 types of dryer pricing Fixed Vend Pricing Accumulator PricingSet-Up Codes Start Operating Set-upExplanation Code ExplanationOptions 3.XX 9.XX to USE if Special Pricing is Selected Code Explanation Value of Coin Special Price Start HourCE Clear Escrow Option Cd Payment Mode COIN/DEBIT OptionMULTI-LOAD Washer and Dryer Warranty
Top Page Image Contents