Maytag W10335465B Connecting 3-Wire Connection Optional, Leveling Stacked Washer/Dryer

Page 27

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Connecting 3-Wire Connection: Optional

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

Connecting Neutral Wire

	1. Remove center terminal block screw. Also remove neutral	3. Connect remaining wires to outer terminal block.
	ground wire by removing external ground conductor screw.	3. Connect remaining wires to outer terminal block.
	ground wire by removing external ground conductor screw.

2.Connect neutral wire and neutral wire of power supply cord/ cable to center terminal block.

4.Connect a separate copper ground wire from the external ground conductor to an adequate ground.

LEVELING

Leveling Stacked Washer/Dryer

Leveling your washer/dryer properly reduces excess noise and vibration.

Not Level

LEVEL

Not Level

1.Remove cardboard from beneath washer/dryer. Place a level on top edges of washer/dryer, checking each side and front. If not level, tip washer/dryer and adjust feet up or down as shown in Steps 3 and 4, repeating as necessary.

Image 27

Contents Installation Instructions Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Stacked WASHER/DRYER Safety Tools & Parts Tools NeededParts Supplied Alternate Parts and Accessories AccessoriesAlternate Parts DIMENSIONS/CLEARANCES DimensionsClearances Stacked Washer/Gas Dryer Location Stacked WASHER/GAS Dryer Installation RequirementsStacked Washer/Gas Dryer Grounding Stacked Washer/Gas Dryer Electrical RequirementsStacked Washer/Gas Dryer Gas Supply Stacked WASHER/ELECTRIC Dryer Installation Requirements Stacked washer/electric dryer installation clearancesStacked Washer/Electric Dryer Location Stacked Washer/Electric Dryer Electrical Requirements Electrical Connection It is your responsibility Electric Dryer Power Supply CordIf using a power supply cord Dryer Electrical RequirementsDryer Direct Wire If connecting by direct wire Rigid metal vent Dryer Venting RequirementsElbows ClampsVent System Length Vent HoodsMultiple Dryer Venting If an Exhaust Hood Cannot be UsedDryer GAS Supply Requirements Type of GasGas Supply Line Remove Transport System Installing Stacked WASHER/DRYERClear Water Lines Connect Inlet HosesConnect Inlet Hoses to Washer Connect Inlet Hoses to Water FaucetsLaundry tub drain or standpipe drain Route Drain HoseSecure Drain Hose Remove drain hose from the washer drumFloor Washer Drain SystemStandpipe drain system wall or floor Wall Laundry tub drain systemStrain Relief Direct Wire Strain ReliefPower Supply Cord Strain Relief Electric Dryer Electrical ConnectionsConnection Options Connecting 4-Wire Connection Power Supply CordConnecting Neutral Wire Connecting 3-Wire Connection Power Supply CordConnecting 4-Wire Connection Direct Wire Standard Power Cord ConnectorsConnecting Remaining Wires Connecting 3-Wire Connection Direct WireConnecting 3-Wire Connection Optional LevelingLeveling Stacked Washer/Dryer Complete Installation Remove the Door Assembly Reversing Dryer Door SwingReverse Hinge Replace the Door Assembly Reinstall the doorReverse the strike Washer Stacked WASHER/DRYER Maintenance InstructionsCleaning the Door Seal/Bellow To clean washer interior Maintenance InstructionsDryer If YOU Need AssistanceDryer control Electronic Control Setup InstructionsGeneral Washer/Dryer User Information Washer controlAccumulator Pricing Control Set-up ProceduresHow to Use the Buttons to Program the Controls There are four 4 types of dryer pricing Fixed Vend PricingCode Explanation Start Operating Set-upSet-Up Codes ExplanationOptions 3.XX 9.XX to USE if Special Pricing is Selected Code Explanation Value of Coin Special Price Start HourCE Clear Escrow Option Cd Payment Mode COIN/DEBIT OptionMULTI-LOAD Washer and Dryer Warranty