LG Electronics DLE2511W, D5932W, D2532W, D5911W, D2511W manual 12.7cm

Page 14

ELECTRICAL REQUIREMENTS - ELECTRICAL DRYER

Customer Service Troubleshooting Tips Operating Instruction Installation Instructions Safety Instructions

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw.

1"5cm) . (2

5" (12.7cm)

1. Remove center terminal block screw.

2. Remove appliance ground wire (green) from external ground connector screw. Fasten it under center, silver colored terminal block screw.

3. Connect ground wire (green or bare) of power supply cable to external ground conductor screw. Tighten screw.

1

4

 

5

2

6

 

3

 

1.External ground connector

2.Green or bare copper wire of power supply cord

3.3/4 in. (1.9 cm) UL-listed strain relief

4.Center silver-colored terminal block screw

5.Neutral grounding wire (green)

6.Neutral wire (white)

4. Place the hooked end of the neutral wire (white wire) of power supply cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

5. Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

1

2

4

5

3

7

6

1.3-wire receptacle (NEMA type 10-30R)

2.3-wire plug

3.Neutral prong

4.Spade terminals with up turned ends

5.3/4 in. (1.9 cm) UL approved strain relief

6.Ring terminals

7.Neutral (white or center wire)

1. Loosen or remove center terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver colored terminal screw of the terminal block. Tighten screw.

1

3

 

4

2

5

1.External ground connector

2.Neutral grounding wire (green)

3.Center silver-colored terminal block screw

4.Neutral wire (white or center wire)

5.3/4 in. (1.9 cm) UL-listed strain relief

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

1 4

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Electric and Gas Dryer Table of Contents Before Using Your NEW DryerWhat to do if YOU Smell GAS Important Safety Instructions Important Safety InstructionsLG Dryer Warranty RequirementsMinimum installation spacing for a recessed Installation InstructionsInstallation clearances InstallationPosition and Level the Dryer Installing the DryerFailure to exhaust dryer properly will void warranty Connect Dryer Exhaust SystemConnect Gas Supply Pipe Gas Dryer only RequirementsHeat Source Check Door Reversal Procedure Manufactured Mobile Home Installation Electrical Requirements Electrical Dryer Grounding InstructionsWire connection Power supply cord Wire connection Direct wire12.7cm Wire connection Direct wire Electrical Requirements GAS Dryer Grounding Instructions GAS Requirements Supply line requirementsExhaust System Exhaust RequirementsExhaust System Materials Maximum length of 4 10.2 cm diameter rigid metal duct Maximum length of 4 10.2 cm diameter flexible metal ductExhaust System Maintenance Dryer AirflowUser Maintenance Cleaning the Lint ScreenFeatures and Benefits Starting Your Dryer Fire Hazard No washer can completely remove oilTo use a Manual Dry Cycle Pausing or RestartingTo use a Sensor Dry Cycle Stopping Your DryerCycle Descriptions Modifiers OptionsTo recall your stored Custom Program To use the Rack DRYTo store a Custom Program Before YOU Call for Service Problem Possible Causes What To DoService Telephone Numbers LG Dryer Limited Warranty USA
Top Page Image Contents