ADC ML-82 service manual Basket and Support Assembly, Temperature Sensor Bracket Assembly

Page 16

D. THE BASKET AND SUPPORT ASSEMBLY

The basket and support assembly is designed for 80 lbs. (36 km) of dry material. It is supported by a shaft and two (2) bearings.

E.TEMPERATURE SENSOR BRACKET ASSEMBLY

This bracket assembly is equipped with two (2) important devices. One is the temperature probe and the other is the 225º F (107º C) basket hi-limit. The temperature probe senses the temperature in the basket and sends a signal to the computer to read that temperature. This sensor is also known as the “TEMP SENSOR FAIL” sensor. The 225º F (107º C) thermostat is a safety device to shut down the gas valve in a case of the temperature exceeding 225º F (107º C).

F. TUMBLER BEARING ASSEMBLY

The bearing box is the holder for the pillow block bearing and it also has the adjustments for the basket on it. The bearings are what support the tumbler support and basket to the dryer. The rotational sensor is another safety device to stop the motor if it senses the basket has stopped during a cycle.

12

Image 16
Contents ML-82 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section SERVICE/PARTS Information Safety Precautions Important InformationStandards SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications MLG-82 Gas MLS-82 Steam Component Identification Page Routine Maintenance CleaningAdjustments LubricationControl Panel Assembly Door Switch AssemblyLint Drawer Lint Drawer Switch Description of PartsTemperature Sensor Bracket Assembly Basket and Support AssemblyTumbler Bearing Assembly DRIVE/FAN Mount Assembly Idler ARM AssemblyBlower Motor Sail Switch Assembly HSI HOT Surface Ignition Burner BOX AssemblyFront Panel Assembly Reversing Relay Panel Servicing IntroductionTo Replace Keyboard Label Assembly To Replace Microprocessor Temperature Sensor ProbeComputer Controls To Replace Computer BoardIgnition Controls To Remove Hot Surface IgnitorTo Remove Flame Sensor Probe HSI Ignitor Flame Sensor ProbeTo Replace Gas Valve Refer to burner illustration on To Test and Adjust Gas Water Column PressureTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace HSI Module To Replace Burner TubesTo Replace Burner HI-LIMIT Thermostat GAS Models only Sail Switch Assembly GAS Models only To Replace Sail Switch To Adjust Sail SwitchTo Replace Main Door Assembly To Install New Main Door GlassTo Replace Front Panel To Replace Main Door Hinge BlockSteam Controls Installation To Replace Steam Coil Damper SystemTo Replace Piston To Replace The Needle ValveTo Replace the 3-Way Micro Valve To Replace Steam CoilTo Replace Tumbler Pulley Reversing Tumbler and Bearing AssemblyTo Replace The Rear Tumbler Bearing Idler Shaft and Bearing Assembly To Replace The Front Tumbler BearingTo Replace Idler Pulley To Replace Idler BearingTumbler Basket Drive PulleyTumbler Alignment Vertical Tumbler Alignment Lateral To Replace The Tumbler And/Or Tumbler SupportBelt Tension Adjustment-Tumbler To Idler Belts Refer to Illustrations in Sections I and KBelt Tension Alignment Motor To Idler To Replace V-BeltsPhase 6 OPL System Diagnostics Diagnostic L.E.D. Display Failure CodesPage E.D. Light Emitting Diode Display Indicators E.D. Display Indicator NumberPage FAN Blower Output L.E.D. light emitting diode Indicator AIR AIR JET Output L.E.D. Indicator OptionalHT1 Heat Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorLint Lint Door Input L.E.D. light emitting diode Indicator Main Main Door Input L.E.D. IndicatorDrum Tumbler HI-LIMIT Input L.E.D. Indicator Sail Sail Switch Input L.E.D. IndicatorPower Supply Input L.E.D. Indicator E.D. Codes Fault Codes GAS Models only Power 24 VAC is not Evident AT GAS ValveGAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit GAS only Ignition Attempt FailureTroubleshooting Computer will not accept keypad touchpad entriesDryer operates but is taking too long to dry Drive motor runs, burner is on, but basket will not turnThermal overload for drive motor is tripping Burner hi-limit safety thermostat is tripping Overload for impellor fan motor is trippingThere is excessive vibration coming from the basket Electrical Troubleshooting No Display Condition Drive motor reverses but does not forward, blower motor runsBlower motor does not operate, drive motor runs Lint Door ConditionMain Door Condition Temp Sensor Fail CheckMotor Plate High and LOW Voltage Technical InformationFor example Data Label Contact American Dryer CorporationData Label Model Dryer American Gas Association, Canadian Gas AssociationManual Reset HI-LIMIT Instructions Computer Logic Service SERVICE/PARTS InformationParts Returning Warranty Cards Warranty InformationReturning Warranty Parts Page ML-82 Tool List ADC 450404 1- 12/21/99-50