ADC ML-82 service manual To Replace Main Door Assembly, To Install New Main Door Glass

Page 28

To Replace Main Door Assembly

1.Open main door.

2.Holding the door upward remove the two (2) screws from the top hinge block.

3.Lift the door up to remove.

4.Reverse this procedure for reinstalling new main door assembly.

To Install New Main Door Glass

1.Remove main door assembly from dryer (follow main door removal procedure).

2.Lay main door on flat surface with back of door face down.

3.Remove glass and clean all old sealant off main door. This area must be completely clean for correct bonding.

4.Apply a narrow bead of silicone (ADC P/N 170730) all around main door area where glass will rest.

5.Install glass onto door and adhesive. Slightly/gently press glass into place.

6.The door assembly should now be put in an area where it will not be disturbed for a few hours. This will give the silicone a chance to harden.

IMPORTANT: DO NOT press hard or silicone thickness between the glass and door will be reduced, resulting in poor bonding.

24

Image 28
Contents ML-82 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section SERVICE/PARTS Information Safety Precautions Important InformationStandards SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications MLG-82 Gas MLS-82 Steam Component Identification Page Routine Maintenance CleaningAdjustments LubricationControl Panel Assembly Door Switch AssemblyLint Drawer Lint Drawer Switch Description of PartsTemperature Sensor Bracket Assembly Basket and Support AssemblyTumbler Bearing Assembly DRIVE/FAN Mount Assembly Idler ARM AssemblyBlower Motor Sail Switch Assembly HSI HOT Surface Ignition Burner BOX AssemblyFront Panel Assembly Reversing Relay Panel Servicing IntroductionTo Replace Keyboard Label Assembly To Replace Microprocessor Temperature Sensor ProbeComputer Controls To Replace Computer BoardIgnition Controls To Remove Hot Surface IgnitorTo Remove Flame Sensor Probe HSI Ignitor Flame Sensor ProbeTo Replace Gas Valve Refer to burner illustration on To Test and Adjust Gas Water Column PressureTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace HSI Module To Replace Burner TubesTo Replace Burner HI-LIMIT Thermostat GAS Models only Sail Switch Assembly GAS Models only To Replace Sail Switch To Adjust Sail SwitchTo Replace Main Door Assembly To Install New Main Door GlassTo Replace Front Panel To Replace Main Door Hinge BlockSteam Controls Installation To Replace Steam Coil Damper SystemTo Replace Piston To Replace The Needle ValveTo Replace the 3-Way Micro Valve To Replace Steam CoilTo Replace Tumbler Pulley Reversing Tumbler and Bearing AssemblyTo Replace The Rear Tumbler Bearing Idler Shaft and Bearing Assembly To Replace The Front Tumbler BearingTo Replace Idler Pulley To Replace Idler BearingTumbler Basket Drive PulleyTumbler Alignment Vertical Tumbler Alignment Lateral To Replace The Tumbler And/Or Tumbler SupportBelt Tension Adjustment-Tumbler To Idler Belts Refer to Illustrations in Sections I and KBelt Tension Alignment Motor To Idler To Replace V-BeltsPhase 6 OPL System Diagnostics Diagnostic L.E.D. Display Failure CodesPage E.D. Light Emitting Diode Display Indicators E.D. Display Indicator NumberPage FAN Blower Output L.E.D. light emitting diode Indicator AIR AIR JET Output L.E.D. Indicator OptionalHT1 Heat Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorLint Lint Door Input L.E.D. light emitting diode Indicator Main Main Door Input L.E.D. IndicatorDrum Tumbler HI-LIMIT Input L.E.D. Indicator Sail Sail Switch Input L.E.D. IndicatorPower Supply Input L.E.D. Indicator E.D. Codes Fault Codes GAS Models only Power 24 VAC is not Evident AT GAS ValveGAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit GAS only Ignition Attempt FailureTroubleshooting Computer will not accept keypad touchpad entriesDryer operates but is taking too long to dry Drive motor runs, burner is on, but basket will not turnThermal overload for drive motor is tripping Burner hi-limit safety thermostat is tripping Overload for impellor fan motor is trippingThere is excessive vibration coming from the basket Electrical Troubleshooting No Display Condition Drive motor reverses but does not forward, blower motor runsBlower motor does not operate, drive motor runs Lint Door ConditionMain Door Condition Temp Sensor Fail CheckMotor Plate High and LOW Voltage Technical InformationFor example Data Label Contact American Dryer CorporationData Label Model Dryer American Gas Association, Canadian Gas AssociationManual Reset HI-LIMIT Instructions Computer Logic Service SERVICE/PARTS InformationParts Returning Warranty Cards Warranty InformationReturning Warranty Parts Page ML-82 Tool List ADC 450404 1- 12/21/99-50