ADC ML-82 service manual SERVICE/PARTS Information, Service, Parts

Page 60

SECTION X

SERVICE/PARTS INFORMATION

A. SERVICE

1.Service must be performed by a qualified trained technician, service agency, or gas supplier. If service is required, contact the distributor from whom the ADC equipment was purchased. If the distributor cannot be contacted or is unknown, contact the ADC Service Department for a distributor in your area.

NOTE: When contacting the ADC Service Department, be sure to give them the correct model number and serial number so that your inquiry is handled in an expeditious manner.

B. PARTS

1.Replacement parts should be purchased from the distributor from whom the ADC equipment was pur- chased. If the distributor cannot be contacted or is unknown, contact the ADC Parts Department for a distributor in your area. Parts may also be purchased directly from the factory by calling the ADC Parts Department at (508) 678-9000 or you may FAX in your order at (508) 678-9447.

NOTE: When ordering replacement parts from the ADC dealer or the ADC factory be sure to give them the correct model number and serial number so that your parts order can be processed in an expeditious manner.

56

Image 60
Contents ML-82 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section SERVICE/PARTS Information Safety Precautions Important InformationStandards SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications MLG-82 Gas MLS-82 Steam Component Identification Page Routine Maintenance CleaningAdjustments LubricationControl Panel Assembly Door Switch AssemblyLint Drawer Lint Drawer Switch Description of PartsBasket and Support Assembly Temperature Sensor Bracket AssemblyTumbler Bearing Assembly Idler ARM Assembly DRIVE/FAN Mount AssemblyBlower Motor HSI HOT Surface Ignition Burner BOX Assembly Sail Switch AssemblyFront Panel Assembly Reversing Relay Panel Servicing IntroductionTo Replace Keyboard Label Assembly To Replace Microprocessor Temperature Sensor ProbeComputer Controls To Replace Computer BoardIgnition Controls To Remove Hot Surface IgnitorTo Remove Flame Sensor Probe HSI Ignitor Flame Sensor ProbeTo Test and Adjust Gas Water Column Pressure To Replace Gas Valve Refer to burner illustration onTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner Tubes To Replace HSI ModuleTo Replace Burner HI-LIMIT Thermostat GAS Models only Sail Switch Assembly GAS Models only To Replace Sail Switch To Adjust Sail SwitchTo Replace Main Door Assembly To Install New Main Door GlassTo Replace Front Panel To Replace Main Door Hinge BlockSteam Controls Installation To Replace Steam Coil Damper SystemTo Replace Piston To Replace The Needle ValveTo Replace the 3-Way Micro Valve To Replace Steam CoilTumbler and Bearing Assembly To Replace Tumbler Pulley ReversingTo Replace The Rear Tumbler Bearing Idler Shaft and Bearing Assembly To Replace The Front Tumbler BearingTo Replace Idler Pulley To Replace Idler BearingDrive Pulley Tumbler BasketTumbler Alignment Vertical Tumbler Alignment Lateral To Replace The Tumbler And/Or Tumbler SupportBelt Tension Adjustment-Tumbler To Idler Belts Refer to Illustrations in Sections I and KBelt Tension Alignment Motor To Idler To Replace V-BeltsPhase 6 OPL System Diagnostics Diagnostic L.E.D. Display Failure CodesPage E.D. Light Emitting Diode Display Indicators E.D. Display Indicator NumberPage FAN Blower Output L.E.D. light emitting diode Indicator AIR AIR JET Output L.E.D. Indicator OptionalHT1 Heat Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorLint Lint Door Input L.E.D. light emitting diode Indicator Main Main Door Input L.E.D. IndicatorDrum Tumbler HI-LIMIT Input L.E.D. Indicator Sail Sail Switch Input L.E.D. IndicatorPower Supply Input L.E.D. Indicator E.D. Codes Fault Codes GAS Models only Power 24 VAC is not Evident AT GAS ValveGAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit GAS only Ignition Attempt FailureTroubleshooting Computer will not accept keypad touchpad entriesDrive motor runs, burner is on, but basket will not turn Dryer operates but is taking too long to dryThermal overload for drive motor is tripping Burner hi-limit safety thermostat is tripping Overload for impellor fan motor is trippingThere is excessive vibration coming from the basket Electrical Troubleshooting No Display Condition Drive motor reverses but does not forward, blower motor runsBlower motor does not operate, drive motor runs Lint Door ConditionMain Door Condition Temp Sensor Fail CheckTechnical Information Motor Plate High and LOW VoltageFor example Data Label Contact American Dryer CorporationData Label Model Dryer American Gas Association, Canadian Gas AssociationManual Reset HI-LIMIT Instructions Computer Logic SERVICE/PARTS Information ServiceParts Warranty Information Returning Warranty CardsReturning Warranty Parts Page ML-82 Tool List ADC 450404 1- 12/21/99-50