ADC ML-82 service manual There is excessive vibration coming from the basket

Page 50

K. There is excessive vibration coming from the basket...

1.Basket is out of adjustment.

2.Drive shaft or idler shaft is out of alignment.

3.Faulty pillow block bearing.

4.Faulty tumbler wheel.

5.Drive motor and shaft not aligned.

6.Faulty retaining wheel.

46

Image 50

Contents ML-82 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section SERVICE/PARTS Information Safety Precautions Important InformationStandards SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications MLG-82 Gas MLS-82 Steam Component Identification Page Routine Maintenance CleaningAdjustments LubricationLint Drawer Lint Drawer Switch Control Panel AssemblyDoor Switch Assembly Description of PartsTumbler Bearing Assembly Basket and Support AssemblyTemperature Sensor Bracket Assembly Blower Motor Idler ARM AssemblyDRIVE/FAN Mount Assembly Front Panel Assembly HSI HOT Surface Ignition Burner BOX AssemblySail Switch Assembly Reversing Relay Panel Servicing IntroductionComputer Controls To Replace Keyboard Label AssemblyTo Replace Microprocessor Temperature Sensor Probe To Replace Computer BoardTo Remove Flame Sensor Probe Ignition ControlsTo Remove Hot Surface Ignitor HSI Ignitor Flame Sensor ProbeTo Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve Refer to burner illustration on To Convert Natural Gas to L.P. Gas To Replace Burner HI-LIMIT Thermostat GAS Models only To Replace Burner TubesTo Replace HSI Module Sail Switch Assembly GAS Models only To Replace Sail Switch To Adjust Sail SwitchTo Replace Main Door Assembly To Install New Main Door GlassTo Replace Front Panel To Replace Main Door Hinge BlockSteam Controls Installation To Replace Steam Coil Damper SystemTo Replace the 3-Way Micro Valve To Replace PistonTo Replace The Needle Valve To Replace Steam CoilTo Replace The Rear Tumbler Bearing Tumbler and Bearing AssemblyTo Replace Tumbler Pulley Reversing To Replace Idler Pulley Idler Shaft and Bearing AssemblyTo Replace The Front Tumbler Bearing To Replace Idler BearingTumbler Alignment Vertical Drive PulleyTumbler Basket Tumbler Alignment Lateral To Replace The Tumbler And/Or Tumbler SupportBelt Tension Adjustment-Tumbler To Idler Belts Refer to Illustrations in Sections I and KBelt Tension Alignment Motor To Idler To Replace V-BeltsPhase 6 OPL System Diagnostics Diagnostic L.E.D. Display Failure CodesPage E.D. Light Emitting Diode Display Indicators E.D. Display Indicator NumberPage HT1 Heat Output L.E.D. Indicator FAN Blower Output L.E.D. light emitting diode IndicatorAIR AIR JET Output L.E.D. Indicator Optional Fuse Main Fuse Input L.E.D. IndicatorDrum Tumbler HI-LIMIT Input L.E.D. Indicator Lint Lint Door Input L.E.D. light emitting diode IndicatorMain Main Door Input L.E.D. Indicator Sail Sail Switch Input L.E.D. IndicatorPower Supply Input L.E.D. Indicator E.D. Codes GAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT Circuit Fault CodesGAS Models only Power 24 VAC is not Evident AT GAS Valve GAS only Ignition Attempt FailureTroubleshooting Computer will not accept keypad touchpad entriesThermal overload for drive motor is tripping Drive motor runs, burner is on, but basket will not turnDryer operates but is taking too long to dry Burner hi-limit safety thermostat is tripping Overload for impellor fan motor is trippingThere is excessive vibration coming from the basket Electrical Troubleshooting No Display Condition Drive motor reverses but does not forward, blower motor runsBlower motor does not operate, drive motor runs Lint Door ConditionMain Door Condition Temp Sensor Fail CheckFor example Technical InformationMotor Plate High and LOW Voltage Data Label Contact American Dryer CorporationData Label Model Dryer American Gas Association, Canadian Gas AssociationManual Reset HI-LIMIT Instructions Computer Logic Parts SERVICE/PARTS InformationService Returning Warranty Parts Warranty InformationReturning Warranty Cards Page ML-82 Tool List ADC 450404 1- 12/21/99-50