Maytag MDG-30 manual $785$

Page 28

2. Technical Gas Data

a. Gas Specifications

0HDVXUHG￿DW￿RXWOHW￿VLGH￿RI￿

TYPE OF GAS

 

 

 

1$785$/

 

/,48,'￿3523$1(

 

 

 

 

 

0DQLIRO 3UHVVXUH

 

LQFKHV:&

 

LQFKHV:&

 

 

 

 

 

￿￿￿,QOLQH3UHVV

JDV￿YDOYH￿SUHVVXUH￿WDSLQFKHV￿ZKHQ￿JDV:￿YDOYH&￿LV￿R

Q￿

LQFKHV:&

 

 

 

 

 

b.Gas Connections

Inlet connection ------------ 3/4" inch N.P.T.

Inlet supply size ------------ 3/4" inch N.P.T. (minimum) Btu/hr input (per dryer) --- 176,000 (MDG-30D Fast Dry)

1)Natural Gas

Regulation is controlled by the dryer's gas valve's internal regulator. Incoming supply pressure must be consistent between a minimum of 6.0 inches and a maximum of 12.0 inches water column (W.C.) pressure.

2)Liquid Propane (L.P.) Gas

Dryers made for use with L.P. gas have the gas valve's internal pressure regulator blocked open so that the gas pressure must be regulated upstream of the dryer. The pressure measured at each gas valve pressure tap must be a consistent 10.5 inches water column (W.C.). There is no regulator or regulation provided in an L.P. dryer. The water column (W.C.) pressure must be regulated at the source (L.P. tank) or an external regulator must be added to each dryer.

 

 

 

 

 

TYPE OF GAS

 

/3

 

 

 

 

 

 

 

 

 

&RQYHUVLRQ

$’&

%78

 

 

1DWXUDO

 

/LTXLG3URSDQH

 

 

 

.LW

02’(/

3HU+RXU

 

4W\

’06

3DUW

4W\

’06

3DUW

 

3DUW1XPEHU

80%(5

5DWLQJ

 

1XPEHU

1XPEHU

0’*’

 

￿DV￿IROORZV￿











￿1DWXUDO￿*DV￿￿￿￿￿￿￿￿￿￿￿/LTXLG'￿0￿6￿￿3URSDQH*DV￿'ULOO￿0DWHULDO￿￿￿￿6L]H￿￿￿￿HTXLYDOHQWVDUH￿￿￿￿￿￿

)DVW’U\

 

 

 

 

 

 

 

 

 

24

Image 28
Contents MDG-30 Fast Dry Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Technical Information Section Safety Precautions Personal Injury or Fire could ResultOsha Occupational Safety and HealthAdministration Standards ADJUSTING, INSTALLATION, or Testing Ofany Equipment perGAS Supply Before ANY Covers or Guards are Removed Specifications SuperSpecifications MDG-30 Fast Dry Installation Procedures Location Requirements Dryer Enclosure Requirements Fresh AIR Supply Exhaust Requirements Single Dryer Venting Illus. B Multiple Dryer Common Venting ILLUS. D Importantventingreminders Electrical Information Electrical RequirementsMust be Provided Odfn Klwh Uhhq Important a Circuit Serving Each Dryer Must be Provided DG-30 Fast DRY GAS GAS Information Injury and Improper Operation of the Dryer$785$ Page Page Preparation for Operation and START-UP Preoperational Tests GAS Models onlyPreoperational Instructions Page OPL Models Shut Down Instructions Service PartsReturning Warranty Cards SectionRoutine Maintenance CleaningAdjustments LubricationNo L.E.D. light emitting diode display Drive motor not operating does not startBlower motor not operating does not start Microprocessor computer display reads dSFLMicroprocessor controller computer display reads door No heat, ignitor sparks, burner goes on and off right awayDryer operates but is taking too long to dry Dryer or scraping noise at basket tumbler area Condensation on main door glassExcessive noise or vibration Main burners are burning with a yellow flame Heating unit not operating ALL temperature selectionsDryer operates but is taking too long to dry load Dryer is cycling on hi-limit thermostat Technical Information Data LabelSerial Number Procedure for Functional Check Replacement Components Direct Spark Ignition DSI System MAYTAG-113069 1-01/29/99-250