Maytag MDG-30 manual OPL Models

Page 35

b.Select Temperature

The dryer will start, the L.E.D. (light emitting diode) display will read the temperature cycle selected, and the drying time portion of the L.E.D. (light emitting diode) display will read "00" and count upward as time elapses, or the vended time will count downward, depending on the program parameter setting.

IMPORTANT: If the door is opened during a cycle, both the heat and motor will stop. However, the microprocessor controller (computer) will continue to count the time, either upward or downward, depending on which parameter is programmed. Continuation of the cycle will resume only after the door has been closed and any other of the three (3) temperature selection buttons is again depressed.

c. Once the preprogrammed dryness level and cool down period has been reached or the maximum automatic time has expired, whichever comes first, the tone (buzzer) will sound for five (5) seconds, and the L.E.D. (light emitting diode) display will read "donE," at which time the dryer will shut off.

NOTES: 1. If theAnti-Wrinkle program is active, the L.E.D. (light emitting diode) display will continue to read "donE," and the microprocessor controller (computer) will proceed through the Anti-Wrinkle program until the maximum "Active Guard Time" has expired or until the door is opened, whichever comes first. The L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

2.If theAnti-Wrinkle program is not active or in use, the L.E.D. (light emitting diode) display will read "FILL" or "FrEE."

4.Non-Microprocessor (Computer) Models

a.Turn power on to the dryer.

b.Insert coins - rotary meter type ONLY.

c.Select temperature by using rocker switch and selecting "HI TEMP," "LO TEMP," or "PERM PRESS."

d.Press "Push to Start" button to start the cycle.

e.Upon completion of the drying and cooling cycles the dryer will shut off.

NOTE: If the door is opened during a cycle, both the heat and motor will stop. Continuation of the cycle will only resume after the door has been closed, and the "Push to Start" button is pressed.

OPL MODELS

1.To start the dryer:

a.Microprocessor (computer) dryers

1)The L.E.D. (light emitting diode) display will read "FILL."

31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents MDG-30 Fast Dry Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Technical Information Section Personal Injury or Fire could Result Safety PrecautionsGAS Supply Before ANY Covers or Guards are Removed ADJUSTING, INSTALLATION, or Testing Ofany Equipment perOsha Occupational Safety and HealthAdministration Standards Super SpecificationsSpecifications MDG-30 Fast Dry Installation Procedures Location Requirements Dryer Enclosure Requirements Fresh AIR Supply Exhaust Requirements Single Dryer Venting Illus. B Multiple Dryer Common Venting ILLUS. D Importantventingreminders Electrical Requirements Electrical InformationMust be Provided Odfn Klwh Uhhq Important a Circuit Serving Each Dryer Must be Provided DG-30 Fast DRY GAS Injury and Improper Operation of the Dryer GAS Information$785$ Page Page Preparation for Operation and START-UP GAS Models only Preoperational TestsPreoperational Instructions Page OPL Models Shut Down Instructions Parts ServiceSection Returning Warranty CardsCleaning Routine MaintenanceLubrication AdjustmentsDrive motor not operating does not start No L.E.D. light emitting diode displayMicroprocessor computer display reads dSFL Blower motor not operating does not startNo heat, ignitor sparks, burner goes on and off right away Microprocessor controller computer display reads doorDryer operates but is taking too long to dry Excessive noise or vibration Condensation on main door glassDryer or scraping noise at basket tumbler area Dryer operates but is taking too long to dry load Heating unit not operating ALL temperature selectionsMain burners are burning with a yellow flame Dryer is cycling on hi-limit thermostat Data Label Technical InformationSerial Number Procedure for Functional Check Replacement Components Direct Spark Ignition DSI System MAYTAG-113069 1-01/29/99-250
Top Page Image Contents