Maytag W10562339B-SP, W10562335B installation instructions Location Requirements, You will need

Page 4

LOCATION REQUIREMENTS

INSTALLATION CLEARANCES

Location must be large enough to allow dryer door to open fully.

DRYER DIMENSIONS

Models with riser

You will need:

■■ A location allowing for proper exhaust installation. See “Venting Requirements.”

■■ A separate 30 amp circuit.

■■ If using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See “Electrical Requirements.”

■■ Floor must support dryer weight of 200 lbs. (90.7 kg). Also consider weight of companion appliance.

■■ Level floor with maximum slope of 1" (25 mm) under entire dryer. If slope is greater than 1" (25 mm), clothes may not tumble properly and automatic sensor cycles may not operate correctly.

■■ For a garage installation, place dryer at least 18" (457 mm) above floor.

■■ Steam models only: Cold water faucets located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). You may use the water supply for your washer using the “Y” connector and short hose (if needed) which are provided.

For each arrangement, consider allowing more space for ease of installation and servicing; spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings

in door are required.

IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below 45° F (7° C). Lower temperatures may cause dryer not to shut off at end of automatic sensor cycles, resulting in longer drying times.

Check code requirements. Some codes limit, or do not permit, installing dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

 

 

 

 

 

Side view

 

 

 

 

 

 

 

 

Back view

 

 

 

 

 

 

Models without riser

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side view

Back view

Bottom view:

NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with elbow. See “Venting Requirements.”

4

Image 4
Contents Electric Dryer Installation Instructions Dryer Safety Installation Requirements Tools neededParts supplied all models Parts supplied steam modelsLocation Requirements You will needElectrical Requirements Install Leveling Legs If connecting by direct wirePrepare dryer for leveling legs If your outlet looks like thisAttach power supply cord strain relief Attach power supply cord to strain reliefElectrical Connection Choose electrical connection typeConnect neutral ground wire and neutral wire Connect ground wirePrepare to connect neutral ground wire and neutral wire Connect remaining wiresConnect neutral wire Attach direct wire strain reliefDirect Wire Strain Relief Remove center screwWire Direct Wire Connection Prepare your 4-wire cable for direct connectionIf your wiring looks like this Prepare your 3-wire cable for direct connection Optional 3-wire ConnectionVenting Connect external ground wireRigid metal vent Plan Vent System Whirlpool Vent System Chart Alternate installations for close clearancesSpecial provisions for mobile homes Determine vent pathInstall Vent System Connect Inlet HosesAttach long hose to Y connector and tighten couplings Attach long hose to dryer fill valve and tighten couplingTurn on cold water faucet Check for leaksAdjust leveling legs Connect VentLevel Dryer Move dryer to final locationComplete Installation Checklist Remove the door assemblyReverse Door Swing Steam models onlyReinstall the door Reverse the strike2013 05/13 All rights reserved