Maytag W10131619A installation instructions Venting Requirements, If using an existing vent system

Page 13

4.Tighten strain relief screws.

5.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold- down screw.

6.Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

Venting Requirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building.

If using an existing vent system

Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

Use a heavy metal vent. Do not use plastic or metal foil vent.

4" (102 mm) heavy metal exhaust vent and clamps must be used.

4"

102 mm

4" (102 mm) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more information, see the “Assistance or Service” section.

Rigid metal vent

For best drying performance, rigid metal vents are recommended.

Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

Flexible metal vents are acceptable only if accessible for cleaning.

Flexible metal vent must be fully extended and supported when the dryer is in its final location.

Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

Do not install flexible metal vent in enclosed walls, ceilings, or floors.

The total length of flexible metal vent should not exceed 73/4 ft (2.4 m).

Elbows

45° elbows provide better airflow than 90° elbows.

GoodBetter

Clamps

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Items sticking through the vent can catch lint. Do not use duct tape.

Clamp

13

Image 13
Contents W10131619A Electric DryerDryer Safety Table of ContentsImportant Safety Instructions Tools and Parts Installation InstructionsLocation Requirements Electrical Requirements Mobile Home Additional Installation RequirementsIt is your responsibility Electrical ConnectionIf connecting by direct wire If using a power supply cordGauge solid copper wire do not use aluminum If your outlet looks like thisStyle 1 Power supply cord strain relief Power Supply Cord Direct WireInstall strain relief Electrical ConnectionStyle 2 Direct wire strain relief Wire connection Power Supply Cord Wire connection Direct Wire Loosen or remove center silver-colored terminal block screw CG FTighten strain relief screw Optional 3-wire connectionVenting Requirements If using an existing vent systemIf this is a new vent system Vent material Exhaust Plan Vent SystemRecommended hood styles are shown here Angled hood style shown here is acceptableAlternate installations for close clearances Install Vent SystemSpecial provisions for mobile home installations Vent system chartConnect Vent Install Leveling LegsLevel Dryer Reverse Door Swing OptionalIf the dryer will not start, check the following Complete InstallationStarting Your Dryer Dryer USEHow Automatic Drying Works Stopping and RestartingCleaning the Lint Screen Cleaning the Dryer LocationDryer Care Drying Rack OptionRemoving Accumulated Lint Cleaning the Dryer InteriorVacation and Moving Care Dryer Operation TroubleshootingDryer Results Stains on load or drum Lint on loadLoads are wrinkled Cycle time too shortAccessories Assistance or ServiceEnhance your dryer with these premium accessories Part Number AccessoryW10131619A