Humminbird 67 manual Start-Up Options Menu, Normal Operation, Simulator

Page 37

Simulator, Shown with Optional

WeatherSenseTM Accessory

		Start-Up Options Menu
		Press the MENU key when the Title screen is displayed to
		access the Start-Up Options menu.
		Use the UP or DOWN 4-WAY Cursor keys to position the cursor,
		then the RIGHT Cursor key to select one of the following
		choices. If you wait too long, the system will default to
		whichever menu mode happens to be highlighted:
		• Normal
		• Simulator
	Start-Up Options Menu	• Simulator
	Start-Up Options Menu	• System Status
		• System Status

•PC Connect (use with PC Connect Cable).

See the following paragraphs for more information about each of these choices.

Normal Operation

Use Normal operation for on the water operation with a transducer connected. In addition, your Matrix Fishing System uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your Matrix Fishing System can be used on the water.

Exit Normal operation by powering your Matrix Fishing System off.

Simulator

Use the Simulator to learn how to use your Matrix Fishing System before taking your boat on the water. The Simulator is a very powerful tool that simulates on the water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation.

NOTE:TogetthefullbenefitoftheSimulator,itisimportanttoselect

Simulator manually from the Start-Up Options menu as opposed to letting the Matrix Fishing System enter Simulator automatically (as it will if a transducer is not connected and you do nothing during

power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre-configure your Matrix Fishing System for on the water operation. Any menu changes you make will be saved for later use.

A message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your Matrix Fishing System off.

31

Image 37

Contents Matrix 67GPS Trackplotter Operations Manual Thank You Table of Contents Navigation X-Press Menu Navigation Views Only Sonar X-Press Menu Sonar Views OnlySonar Menu Tab Setup Menu Tab Alarms Menu TabNavigation Menu Tab Accessories Menu Tab Troubleshooting DualBeam Plus Sonar How Sonar WorksQuadraBeam Sonar How GPS and Cartography Work WideSide SonarWith Optional-Purchase WideSide Transducer Detailed Map Multi-Media Card MMCBait Ball Hard Bottom Rocky Bottom What’s On the Sonar DisplayTo your boat, including the following items 83 kHz, Wide Beam Hollow Fish SymbolSonar views ViewsSonar View Zoom ViewSonar View Sonar ViewReal Time Sonar RTS Window Understanding Sonar HistoryBottom Contour Profile with RTS Window Bottom PresentationPage Sonar Zoom View Sonar Zoom ViewBig Digits View 200/83 kHz Split Sonar View200/83 kHz Split Sonar View Big Digits ViewSide Beam View Side Beam ViewWideSide View WideSide ViewBird’s Eye View Bird’s Eye ViewChart View with Active Cursor Chart ViewView Orientation Combo ViewViewing Cartography Combo ViewPage Waypoints, Routes and Tracks Introduction to NavigationWaypoints, Routes and Tracks Save, Edit, or Delete a Waypoint Navigate to a Waypoint or Position Add a Waypoint Target or Trolling Grid Chart View with GridSave, Edit or Delete a Route Edit, Delete or Hide Saved Tracks Save or Clear a Current TrackKey Functions POWER/LIGHT KeyView Key Info KeyWAY Cursor Control Key Menu KeyMark Key Zoom +/- Key Goto KeyExit Key Powering Up the Unit Accessory BusMatrix 67 Title Screen Menu System Main Menu System Normal User ModeSonar Tab, Normal Mode Sonar Tab, Advanced Mode Normal Operation Start-Up Options MenuSimulator Accessory Test Screen Self Test Accessory Test GPS Diagnostic ViewSystem Status System Status Self Test ScreenPC Connect GPS Diagnostic ViewWith PC Connect Cable Only Sonar X-PressTMMenu To adjust the WideSide ViewSonar Views Only Sonar X-PressTMMenuSensitivity To adjust the SensitivityHighlight Sensitivity on the Sonar X-PressTMmenu Sensitivity at Low Sensitivity at MediumUpper Range To adjust the Upper RangeLower Range To adjust the Lower RangeHighlight Lower Range on the Sonar X-PressTMmenu To adjust the Side Beam Range Chart SpeedTo adjust the Chart Speed Highlight Chart Speed on the Sonar X-Press menuTo adjust the Zoom Level To adjust the Bottom ViewBottom View Zoom LevelSave Current Track Navigation X-PressTMMenuClear Current Track Save Current Route Cancel NavigationSkip Next Waypoint Remove Grid Remove TargetSonar Window Sonar Menu Sonar Menu TabTo use Beam Select Beam SelectHighlight Beam Select on the Sonar main menu To turn Fish ID+TM on or off Fish ID+TMTransducer Cone and Fish Arches KHz Sensitivity Fish SensitivityWideSide Sensitivity KHz BalanceDepth Lines To change the Depth Lines settingDepth Lines Surface Clutter To change the Surface Clutter settingSurface Clutter To change the Max Depth setting To change the Noise Filter settingNoise Filter Max DepthWater Type To change the Water Type settingTransducer Select To change the selected TransducerNavigation Menu Tab Tracks allows you to view the Tracks submenu TracksTo view the Tracks Submenu Highlight Tracks on the Navigation main menuTo view the Waypoints Submenu WaypointsHighlight Waypoints on the Navigation main menu Waypoints Submenu contains the following menu choicesRoutes To change the View Orientation settingTo view the Routes Submenu Routes Submenu contains the following menu choicesTo change the Chart Detail Level setting Chart Detail LevelTo change the Map Borders setting Map BordersSpot Soundings Lat/Lon GridNorth Reference Grid RotationTo change the Track Minimum Distance setting To change the Trackpoint Interval settingTrackpoint Interval Track Min DistanceSet Simulation Position Map DatumSet Map Offset Delete All Nav Data Clear Map OffsetTo Clear Map Offset To Delete All Navigation DataFrom any view, press the Menu key twice to access the Main Alarms Menu TabAlarms Menu Fish ID Alarm Depth AlarmTo change the Depth Alarm setting To change the Fish ID Alarm settingOff Course Alarm Low Battery AlarmTo change the Low Battery Alarm setting Highlight Low Battery Alarm on the Alarms main menuDrift Alarm Arrival AlarmAlarm Tone Setup Menu Tab Setup Menu TabUnits Temp Units DepthUnits Distance Units Speed User ModeLanguage Restore Defaults Triplog ResetTo Reset Triplog To Restore DefaultsTo Select Views Select ViewsSelect Views Advanced, Sonar View Only Select ReadoutsTo Select Readouts Temp Offset Depth OffsetSpeed Calibration Daylight Savings Time Local Time ZonePosition Format Date Format Time FormatAdvanced, International Only To change the Time FormatSonar Nmea OutputFollowing Nmea sentences are output To turn Nmea Output on or offAccessories Menu Tab Accessories Menu TabFishing System Doesn’t Power Up TroubleshootingProblem Possible Cause Display ProblemsPossible Source of Noise Isolation Finding the Cause of NoiseMatrix Fishing System Accessories Specifications Page Monday Friday 800 a.m. to 430 p.m. Central Standard Time Custserv@techsonic.com