Humminbird 595C manual Views Menu Tab, Troubleshooting, FishFinder Doesn’t Power Up

Page 38

FF595_Man_531385-1_A_PrfE.qxd 12/9/2004 2:41 PM Page 74

Views Menu Tab

From any view, press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT 4-WAY Cursor Control key until the Views tab is selected. This menu tab allows you to set the available views to either hidden or visible in the view rotation. The view will be removed from the view rotation if it is set to Hidden and will be displayed in the view rotation if it is set to Visible. The following views are available:

Bird’s Eye View

Chart View

Combo View

Sonar View

Sonar Zoom View

Big Digits View

Accessory Test

GPS Diagnostic View

Views Menu

To Change the View Status of Any View:

1.Highlight the View main menu tab.

2.Use the UP or DOWN 4-WAY Cursor Control keys to select a View.

3.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the status of the view from Hidden to Visible.

Troubleshooting

Before contacting the Humminbird® Customer Resource Center, please read the following section. Taking the time to review these troubleshooting guidelines may allow you to solve a performance problem yourself, and therefore avoid sending your unit back for repair.

FishFinder Doesn’t Power Up

If your FishFinder doesn’t power up, use the Installation Guide that also comes with it for specific confirmation details, making sure that:

the power cable is properly connected to the FishFinder control head,

the power cable is wired correctly, with red to positive battery terminal and black to negative terminal or ground

the fuse is operational

the battery voltage of the power connector is at least 10 Volts.

Correct any known problems, including removing corrosion from the battery terminals or wiring, or actually replacing the battery if necessary.

FishFinder Defaults to Simulator with a Transducer Attached

A connected and functioning transducer will cause the newly-started FishFinder to go into Normal operating mode automatically. If, when you power up the FishFinder, it goes into Simulator mode automatically, even though a transducer is already connected, this means that the control head is not detecting the transducer. Perform the following troubleshooting tasks:

Using the Installation Guide that also comes with your FishFinder, check to make sure that the transducer cable is securely connected to the FishFinder. Reconnect if necessary, and power up the FishFinder again to see if this fixes the problem.

Replace the non-functioning transducer with a known good transducer if available and power up the control head again.

Check the transducer cable. Replace the transducer if the cable is damaged or corroded.

68

69

Image 38
Contents FishFinder 595c Operations Manual Table of Contents Thank YouSetup Menu Tab Powering Up the Unit Menu System Start-Up Options MenuAlarms Menu Tab Sonar X-Press Menu Sonar Views OnlySingle Beam Sonar Views Menu Tab TroubleshootingHow Sonar Works How GPS and Cartography Work Multi-Media Card MMCHigh Sonar Intensity Return Bait Ball KHz Fish SymbolWhat’s On the Sonar Display RTS Real Time Sonar Window Low Sonar Intensity ReturnSonar View Sonar Zoom View Chart View Big Digits ViewViews Sonar viewsBottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window Big Digits View Sonar Zoom ViewBig Digits View Bird’s Eye View Chart ViewChart View with Active Cursor Bird’s Eye ViewViewing Cartography Combo ViewView Orientation Save, Edit, or Delete a Waypoint Introduction to NavigationWaypoints, Routes and Tracks Waypoints, Routes and TracksNavigate to a Waypoint or Position Chart View with TargetAdd a Waypoint Target or Trolling Grid Save or Clear a Current Track Chart View with GridSave, Edit or Delete a Route Key Functions POWER/LIGHT KeyEdit, Delete or Hide Saved Tracks View KeyGoto Key WAY Cursor Control KeyMark Key Zoom +/- KeySonar Tab, Normal Mode Sonar Tab, Advanced Mode Powering Up the UnitMain Menu System Normal User Mode Menu SystemSimulator Start-Up Options MenuNormal Operation System StatusSonar X-Press Menu Position ErrorGPS Diagnostic View Sonar Views OnlySensitivity To adjust the SensitivityTo adjust the Upper Range Upper RangeBottom View Chart SpeedLower Range Clear Current Track Navigation X-Press MenuSave Current Track Save Current RouteRemove Target Cancel NavigationSkip Next Waypoint Remove GridTo turn Fish ID+ on or off Sonar Menu TabFish ID+ Advanced Fish SensitivityDepth Lines Max Depth Surface ClutterNoise Filter Water TypeWaypoints Navigation Menu TabTracks Tracks Submenu contains the following menu choicesMap Borders Chart Detail LevelRoutes Shaded Depth Lat/Lon GridSpot Soundings North ReferenceSet Map Offset Map DatumSet Simulation Position Clear Map OffsetFish ID Alarm Alarms Menu TabDepth Alarm Low Battery AlarmArrival Alarm Temp AlarmOff Course Alarm Drift AlarmTo change the Alarm Tone setting Alarm ToneSetup Menu Tab Setup tab is selectedUnits Speed User ModeUnits Depth Units TempSelect Readouts Triplog ResetRestore Defaults Advanced, Sonar View OnlySpeed Calibration Depth OffsetTemp Offset Local Time ZoneNmea Output Time FormatDate Format SonarFishFinder Defaults to Simulator with a Transducer Attached TroubleshootingFishFinder Doesn’t Power Up Views Menu TabFinding the Cause of Noise Display ProblemsProblem Possible Cause IsolationHumminbird FishFinder Accessories SpecificationsContact Humminbird