SUPER MICRO Computer S120T, SERIES3800 user manual Weight

Page 116

SERIES3800/S120T (7045A-C3/7045A-CT) User's Manual

Expansion Slots

One PCI-Express x16, one PCI-Express x4 (in a x16 slot), two 64-bit 133/100 MHz PCI-X, two PCI 33 MHz and an IPMI slot

Motherboard

7045A-C3: X7DCA-3 (Extended ATX form factor)

7045A-CT: X7DCA-i (Extended ATX form factor)

Dimensions (both): 12 x 13 in (305 x 330 mm)

Chassis

SC743TQ-865-SQ Form Factor: tower/4U rackmount

Dimensions (as tower): (WxHxD) 7 x 17.2 x 25.5 in. (178 x 437 x 648 mm)

Weight

Gross (Bare Bone): 64 lbs. (29.1 kg.)

System Cooling

Two (2) 8-cm low-noise chassis fans

One (1) 9-cm low-noise exhaust fan

Two (2) active CPU heat sinks

System Input Requirements

AC Input Voltage: 100-240V AC auto-range

Rated Input Current: 100 (12A) - 240V (6A)

Rated Input Frequency: 50 to 60 Hz

PFC Power Supply

Rated Output Power: 865W (Part# PWS-865-PQ)

Rated Output Voltages: +3.3V (30A), +5V (30A), +12VALL (70A), +5Vsb (6.5A)

Operating Environment

Operating Temperature: 10º to 35º C (50º to 95º F)

Non-operating Temperature: -40º to 70º C (-40º to 158º F)

Operating Relative Humidity: 8% to 90% (non-condensing)

Non-operating Relative Humidity: 5 to 95% (non-condensing)

D-2

Image 116

Contents SERIES3800/S120T Manual Revision Release Date February 15 Server Installation About This ManualManual Organization IntroductionSystem Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Processors MemoryOnboard SAS Serial ATAServer Chassis Features Backplane Cooling SystemIntel 5100 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PaciﬁcUnpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Preparing to Install the Chassis RailsInstalling the Rack Rails Installing the Rails to the ChassisInstalling the Server into the Rack Installing the Server into a RackChecking the Serverboard Setup Accessing the Inside of the SystemChecking the Drive Bay Setup Checking the DrivesChecking the Airﬂow Power ResetChapter System Interface Control Panel ButtonsControl Panel LEDs Overheat/Fan FailPower Fail Drive Carrier LEDsPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Serverboard Installation Connecting CablesInstalling to the Chassis UnpackingConnecting the Control Panel Connecting Data CablesConnecting Power Cables Control Panel Header Pins I/O PortsInstalling the Processor and Heat Sink Installation ProcedureCPU Installation Gold dot Socket key Installing the Heat Sink Installation Uninstalling the Heat SinkMemory Support Installing MemoryInstalling Memory Modules Dimm Installation Installing an Add-on Card Adding PCI CardsServerboard Details X7DCA-3/X7DCA-i Layout Not drawn to scaleX7DCA-3/X7DCA-i Quick Reference Jumper Description Default SettingConnector Description Connector Deﬁnitions Main ATX Power Supply ConnectorSecondary Power Connectors Processor Power ConnectorOverheat/Fan Fail LED OH Reset ConnectorPower Fail LED Fan Headers Power On LEDNMI Button Chassis Intrusion Wake-On-LANWake-On-Ring LAN1/2 Ethernet PortsPower LED/Speaker Overheat LED/Fan Fail JOH1Universal Serial Bus USB Sgpio HeadersPower SMB I2C Connector Backpanel Power SMB I2C ConnectorSAS Power SMB I2C Connector ATX PS/2 Keyboard and PS/2 Mouse PortsCD Header Front Panel Audio ControlJumper Settings Explanation of JumpersCmos Clear To clear CmosLAN1/2 Enable/Disable Watch Dog Enable/DisableI2C Bus to PCI-X/ Slots I2C Bus to PCI-Exp. SlotsOnboard Indicators Onboard Power LED LE1LAN1/2 LEDs SAS LEDsParallel, Floppy, IDE, and Sata Ports Parallel Printer PortIDE Connector Sata PortsFloppy Drive Connector Chapter Advanced Chassis Setup Chassis Front View Power Power FailFront Control Panel NIC1Installing a New Fan System FansFan Failure Replacing Chassis Cooling FansRemoving a Chassis Fan Mounting a SAS/SATA drive in a Drive Carrier Drive Bay InstallationInstalling/Removing SAS/SATA Drives SAS/SATA Backplane Removing a SAS/SATA Drive CarrierInstalling Components in the 5.25 Drive Bays Removing the Empty Drive BayAdding a DVD/CD-ROM Drive Adding an IDE or Floppy DriveReplacing the Power Supply Power SupplyPower Supply Failure Page System Bios How To Change the Conﬁguration DataStarting the Setup Utility IntroductionRunning Setup Main Bios SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupMain Bios Setup Menu Main Setup Features Bios DateSystem Time System DateType LBA Mode Control Transfer ModeUltra DMA Mode CHS Format Available for Primary/Master onlyNative Mode Operation Serial ATA Sata RAID EnableSata Ahci Available when Sata RAID is Disabled Serial ATAAdvanced Setup XBoot FeaturesQuickBoot Mode QuietBootXMemory Cache Cache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationXpci Conﬁguration XAdvanced Chipset Control XAdvanced Processor Options Echo TPR Hardware Prefetcher Available when supported by the CPUIntel Eist Support Available when supported by the CPU Xcpu Cache Control XI/O Device ConﬁgurationXdmi Event Logging Parallel PortDMA Channel Floppy Disk ControllerXConsole Redirection XHardware Monitor Logic Clear System Event Logging Voltage MonitoringSystem Event Logging XSystem Event Log/System Event Log List Mode XRealtime Sensor Data Supervisor Password Is User Password IsSet Supervisor Password SecuritySet User Password Password on BootBoot Boot Priority Order/Excluded from Boot OrdersExit Keyboard error Keyboard locked Unlock key switchMonitor type does not match Cmos Run Setup System battery is dead Replace and run SetupSystem Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsFail-Safe Timer NMI Failed Allocation Error for deviceEntering Setup Eisa Cmos not writeablePS/2 Mouse Boot Summary Screen Press F1 to resume, F2 to Setup, F3 for previousDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F2 to enter Setup System Bios shadowedVideo Bios shadowed PS/2 MousePage Post Code Description Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Serial ATA Sata Introduction to the Intel ICH9R Serial RAID SetupIntroduction to Serial ATA and Parallel ATA RAID Conﬁgurations Intel Matrix StorageUsing the Intel ICH9R Sata RAID Utility Program Creating, Deleting and Resetting RAID VolumesCreating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Bios Weight Regulatory Compliance