SUPER MICRO Computer S120T, SERIES3800 user manual Power On LED, NMI Button, Fan Headers

Page 48

SERIES3800/S120T (7045A-C3/7045A-CT) User's Manual

HDD LED

The HDD LED connection is located on pins 13 and 14 of JF1. This LED is used to display all IDE and SATA activity. See the table on the right for pin deﬁnitions.

Power On LED

The Power On LED connector is lo- cated on pins 15 and 16 of JF1 (use JLED for a 3-pin connector). This connection is used to provide LED indication of power being supplied to the system. See the table on the right for pin deﬁnitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin deﬁnitions.

Fan Headers

There are eight fan headers on the serverboard, all of which are 4-pin fans. (Pins 1-3 of the fan headers are backward compatible with the traditional 3-pin fans.) See the table on the right for pin deﬁnitions. The onboard fan speeds are controlled by Thermal Management (via Hard- ware Monitoring) under the Advanced Section in the BIOS. The default is disabled. When using Thermal Man- agement setting, please use all 3-pin fans or all 4-pin fans.

HDD LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

13Vcc

14HD Active

Power LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

155V Stby

16Control

NMI Button

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

19Control

20Ground

Fan Header

Pin Deﬁnitions

(FAN1-8)

Pin# Deﬁnition

1Ground (Black)

2+12V (Red)

3Tachometer

4PWM Control

Note: Fan 7 is for the CPU1 and Fan8 is for the CPU2 heat sink.

5-16

Image 48

Contents SERIES3800/S120T Manual Revision Release Date February 15 Server Installation About This ManualManual Organization IntroductionSystem Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Processors MemoryOnboard SAS Serial ATAServer Chassis Features Backplane Cooling SystemIntel 5100 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PaciﬁcChapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Preparing to Install the Chassis RailsInstalling the Rack Rails Installing the Rails to the ChassisInstalling the Server into the Rack Installing the Server into a RackChecking the Serverboard Setup Accessing the Inside of the SystemChecking the Drive Bay Setup Checking the DrivesChecking the Airﬂow Power ResetChapter System Interface Control Panel ButtonsControl Panel LEDs Overheat/Fan FailPower Fail Drive Carrier LEDsPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Serverboard Installation Connecting CablesInstalling to the Chassis UnpackingConnecting Data Cables Connecting Power CablesConnecting the Control Panel Control Panel Header Pins I/O PortsInstalling the Processor and Heat Sink Installation ProcedureCPU Installation Gold dot Socket key Installing the Heat Sink Installation Uninstalling the Heat SinkInstalling Memory Installing Memory ModulesMemory Support Dimm Installation Installing an Add-on Card Adding PCI CardsServerboard Details X7DCA-3/X7DCA-i Layout Not drawn to scaleJumper Description Default Setting Connector DescriptionX7DCA-3/X7DCA-i Quick Reference Connector Deﬁnitions Main ATX Power Supply ConnectorSecondary Power Connectors Processor Power ConnectorReset Connector Power Fail LEDOverheat/Fan Fail LED OH Power On LED NMI ButtonFan Headers Chassis Intrusion Wake-On-LANWake-On-Ring LAN1/2 Ethernet PortsPower LED/Speaker Overheat LED/Fan Fail JOH1Universal Serial Bus USB Sgpio HeadersPower SMB I2C Connector Backpanel Power SMB I2C ConnectorSAS Power SMB I2C Connector ATX PS/2 Keyboard and PS/2 Mouse PortsCD Header Front Panel Audio ControlJumper Settings Explanation of JumpersCmos Clear To clear CmosLAN1/2 Enable/Disable Watch Dog Enable/DisableI2C Bus to PCI-X/ Slots I2C Bus to PCI-Exp. SlotsOnboard Indicators Onboard Power LED LE1LAN1/2 LEDs SAS LEDsParallel, Floppy, IDE, and Sata Ports Parallel Printer PortIDE Connector Sata PortsFloppy Drive Connector Chapter Advanced Chassis Setup Chassis Front View Power Power FailFront Control Panel NIC1Installing a New Fan System FansFan Failure Replacing Chassis Cooling FansRemoving a Chassis Fan Drive Bay Installation Installing/Removing SAS/SATA DrivesMounting a SAS/SATA drive in a Drive Carrier SAS/SATA Backplane Removing a SAS/SATA Drive CarrierInstalling Components in the 5.25 Drive Bays Removing the Empty Drive BayAdding a DVD/CD-ROM Drive Adding an IDE or Floppy DrivePower Supply Power Supply FailureReplacing the Power Supply Page System Bios How To Change the Conﬁguration DataStarting the Setup Utility IntroductionRunning Setup Main Bios SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupMain Bios Setup Menu Main Setup Features Bios DateSystem Time System DateType LBA Mode Control Transfer ModeUltra DMA Mode CHS Format Available for Primary/Master onlyNative Mode Operation Serial ATA Sata RAID EnableSata Ahci Available when Sata RAID is Disabled Serial ATAAdvanced Setup XBoot FeaturesQuickBoot Mode QuietBootXMemory Cache Cache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationXpci Conﬁguration XAdvanced Chipset Control XAdvanced Processor Options Hardware Prefetcher Available when supported by the CPU Intel Eist Support Available when supported by the CPUEcho TPR Xcpu Cache Control XI/O Device ConﬁgurationXdmi Event Logging Parallel PortDMA Channel Floppy Disk ControllerXConsole Redirection XHardware Monitor Logic Voltage Monitoring System Event LoggingClear System Event Logging XSystem Event Log/System Event Log List Mode XRealtime Sensor Data Supervisor Password Is User Password IsSet Supervisor Password SecuritySet User Password Password on BootBoot Boot Priority Order/Excluded from Boot OrdersExit Keyboard error Keyboard locked Unlock key switchMonitor type does not match Cmos Run Setup System battery is dead Replace and run SetupSystem Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsFail-Safe Timer NMI Failed Allocation Error for deviceEntering Setup Eisa Cmos not writeablePS/2 Mouse Boot Summary Screen Press F1 to resume, F2 to Setup, F3 for previousDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F2 to enter Setup System Bios shadowedVideo Bios shadowed PS/2 MousePage Recoverable Post Errors Terminal Post ErrorsPost Code Description Post Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Introduction to the Intel ICH9R Serial RAID Setup Introduction to Serial ATA and Parallel ATASerial ATA Sata RAID Conﬁgurations Intel Matrix StorageUsing the Intel ICH9R Sata RAID Utility Program Creating, Deleting and Resetting RAID VolumesCreating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Bios Weight Regulatory Compliance