Furuno Sc 50 manual Antenna unit SC-603, Mounting, How to orient the antenna elements

Page 17

1. INSTALLATION

1.2.2Antenna unit SC-603

Note: “Bird-repellent fixtures” (supplied) may be attached to each antenna element and the Antenna Cover to prevent birds from alighting on the antenna. If it is more convenient to attach them before fixing the antenna unit to the mounting location, do step 10 in “Welding the antenna unit” before fixing the antenna unit.

Mounting

1.Screw in three antenna elements in the Antenna Base. Remove Antenna Cover and Arm Cover.

Antenna Cover

3
Arm Cover
(Below arm)
Antenna Base	1

2

Antenna

Element

Antenna unit SC-603

2.Pass the coaxial cable from each antenna element through the center of the respective arm and then through the hole at the center of the antenna unit.

3.Orient the three antenna elements so that the protrusion on each faces the bow.

Nut

Arm Cover S

BOW

Orient the three antenna elements so the protrusion on each faces the bow.

How to orient the antenna elements

1-7

Image 17

Contents THD Satellite Compass 00014854802 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingWord to the Owner of the SC-50 FeaturesSystem configuration System ConfigurationStandard supply Equipment ListSC-50 THD Specifications of THD Satellite CompassCoating Color Installing the antenna below superstructures Installing the antenna above superstructuresMounting Considerations Antenna unitAntenna and field of view Mast diameter Separation distance minimumHorizontal separation between antenna and masts Display unit, processor unit Example of antenna installed below superstructuresAntenna unit SC-303 Installing the Antenna UnitMounting dimensions for antenna, orienting the antenna How to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsMounting Antenna unit SC-603Fixing antenna unit to pedestal Orienting the antenna unit top view Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableBulkhead mount Installing the Processor UnitBulkhead mount Processor unit orientation, deck mounting Deck mountInstallation of processor unit on the underside of a desk Installation on the underside of a deskProcessor Unit, rear view Mounting on underside of deskFlush mount Installing the Display UnitDesktop, overhead mounting Flush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Wiring WiringSectional view of coaxial cable DPYC-1.5 How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBSatellite tracking status display Initial SettingsConfirming satellite status Main menu Installation setup menuChoosing mounting method Processor unit, cover opened General wiringConnection of External Equipment Cable Sectional view, fabrication Fabrication of cablesThis page intentionally left blank Display unit ControlsProcessor unit Turning the Power On/OffPanel Illumination, Display Contrast Description of displays Choosing a DisplayHeading display Nav data displayROT Rate-of-Turn display Steering displayCompass display SOG/STW display Speed displayAlarm menu Alarm SetupDgps alarm options Buzzer optionsSatellite status display Confirming Satellite StatusGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Baud rate options Data OUT1 menu, sentencesHeading talker options Tx interval optionsIEC, Nmea version options Sentence and maximum number of characters Output sentence limitationLog pulse options Log pulseGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode Position fix mode options WAAS/DGPS SetupWAAS/DGPS menu Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Restoration options Others MenuOthers menu Trip menu Trip MenuChoosing External Heading Source for Backup Resetting Distance RunReset Distance prompt Heading setup menuPreventive Maintenance MAINTENANCE, TroubleshootingSymptom Cause Remedy TroubleshootingTroubleshooting Diagnostic test1 DiagnosticsTest menu options Test start promptROM, RAM, KEY Test Diagnostic test sequenceTEST2 display Diagnostic test2TEST3 menu Diagnostic test3Alarm options Clearing Data Program NumberProgram number display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryPrompt for exchanging battery Prompt for turning off the powerError Messages Replacement of FuseError Message Meaning Remedy Message displayData ERR Error messages con’t from previousAP-1 Menu TreeDigital Interface AP-3 Schematic diagramsData Data OutAP-4 Data sentencesGNS Gnns fix data AP-5VBW Dual ground/water speed AP-6VLW Distance travelled through the water AP-7AP-8 Port Terminal Name Signal Remarks LabelInput/Output Ports Hdthdghdm AP-9Processor Unit, cover removed Parts List and Parts LocationAP-10 Display Unit, cover opened AP-11AP-12 Geodetic Chart CodesAP-13 Principle of Satellite CompassAP-14 What is WAAS?ＰａｃｋｉｎｇＬｉｓｔ Page 工事材料表 20AT-X-9401 Installation Materials SC-502-J/E 20AY-X-9404 SC-501-J/E 20AY-X-9401 Spare Parts List for ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Page 表示部 IN-1 Index