Furuno Sc 50 manual Resetting Distance Run, Choosing External Heading Source for Backup

Page 56

2. OPERATION

2.13Resetting Distance Run

The distance run may be reset to zero as below when the source of distance run is GPS or VBW.

1.Press the [MENU] key to display the main menu.

2.Choose TRIP MENU and then press the [ENT] key.

3.Choose RESET DISTANCE and then press the [ENT] key.

RESET DISTANCE?

ARE YOU SURE?

YES NO

RESET DISTANCE prompt

4.Choose YES and then press the [ENT] key.

5.Press the [DISP] key to close the menu.

2.14Choosing External Heading Source for Backup

Choose the source of heading data as below.

CAUTION

Never switch from internal to external heading while the autopilot is in the automatic mode. Change to the manual mode before switching.

2. Press the [HDG SETUP] key.

HEADING SETUP

OFFSET : +000.0

(SERVICE ONLY)

HEADING : INT

INT HDG

- - - . - ￿

EXT HDG

- - - . -￿

OFFSET : Heading offset. See service manual for instructions. "SERVICE ONLY" means heading offset shown for display only.

HEADING : Select heading source. Choose INT for normal use. If a gyrocomapss is connected for primary means, leaving this equipment as backup, choose EXT.

INT HDG : Bow heading. Includes offset.

EXT HDG : Heading fed from external equipment.

Heading setup menu

3.”HEADING” is selected; press the [ENT] key.

4.Choose INT or EXT as appropriate. Normally choose INT. If own GPS sensor is not working and a heading sensor such as a gyrocompass is available, choose EXT.

5.Press the [ENT] key.

6.Press the [DISP] key to close the menu.

2-22

Image 56
Contents THD Satellite Compass 00014854802 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures Word to the Owner of the SC-50System Configuration System configurationEquipment List Standard supplyTHD Specifications of THD Satellite Compass SC-50Coating Color Installing the antenna above superstructures Installing the antenna below superstructuresMounting Considerations Antenna unitAntenna and field of view Mast diameter Separation distance minimumHorizontal separation between antenna and masts Example of antenna installed below superstructures Display unit, processor unitAntenna unit SC-303 Installing the Antenna UnitMounting dimensions for antenna, orienting the antenna Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitHow to orient the antenna elements Antenna unit SC-603Mounting Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unit top viewWelding the antenna unit Fastening the antenna cable Antenna elementBulkhead mount Installing the Processor UnitBulkhead mount Deck mount Processor unit orientation, deck mountingInstallation on the underside of a desk Installation of processor unit on the underside of a deskProcessor Unit, rear view Mounting on underside of deskFlush mount Installing the Display UnitDesktop, overhead mounting Flush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Wiring WiringHow to install the optional antenna cable set Sectional view of coaxial cable DPYC-1.5How to attach connector N-P-8DFB How to attach connector N-P-8DFBSatellite tracking status display Initial SettingsConfirming satellite status Main menu Installation setup menuChoosing mounting method Processor unit, cover opened General wiringConnection of External Equipment Fabrication of cables Cable Sectional view, fabricationThis page intentionally left blank Controls Display unitProcessor unit Turning the Power On/OffPanel Illumination, Display Contrast Choosing a Display Description of displaysHeading display Nav data displayROT Rate-of-Turn display Steering displayCompass display Speed display SOG/STW displayAlarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Data OUT1 menu, sentences Baud rate optionsHeading talker options Tx interval optionsIEC, Nmea version options Output sentence limitation Sentence and maximum number of charactersLog pulse Log pulse optionsGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Restoration options Others MenuOthers menu Trip Menu Trip menuResetting Distance Run Choosing External Heading Source for BackupReset Distance prompt Heading setup menuMAINTENANCE, Troubleshooting Preventive MaintenanceSymptom Cause Remedy TroubleshootingTroubleshooting Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence ROM, RAM, KEY TestDiagnostic test2 TEST2 displayTEST3 menu Diagnostic test3Alarm options Program Number Clearing DataProgram number display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRMenu Tree AP-1Digital Interface Schematic diagrams AP-3Data Data OutData sentences AP-4AP-5 GNS Gnns fix dataAP-6 VBW Dual ground/water speedAP-7 VLW Distance travelled through the waterAP-8 Port Terminal Name Signal Remarks LabelInput/Output Ports AP-9 HdthdghdmProcessor Unit, cover removed Parts List and Parts LocationAP-10 AP-11 Display Unit, cover openedGeodetic Chart Codes AP-12Principle of Satellite Compass AP-13What is WAAS? AP-14Packing List Page 工事材料表 20AT-X-9401 Installation Materials SC-502-J/E 20AY-X-9404 SC-501-J/E 20AY-X-9401 Spare Parts List for フラッシュマウントキット 20AY-X-9403 Hatai Page Page Page Page Page 表示部 Index IN-1