Furuno Sc 50 manual How to insert the cable cover, Antenna unit

Page 16

1.INSTALLATION

8.Set the “cable cover” to the antenna base as shown in the figure below.

Cable Cover

How to insert the cable cover

HOW TO REMOVE CABLE COVER

Insert slotted-head screwdriver here to remove cable cover.

9.If necessary, attach nine “bird-repellent fixtures” (supplied) to the antenna cover as shown below. Use the paper pattern to position the fixtures.

Bird-repellent fixture

N

U

R

F	U

Antenna unit

10.Follow paragraph 1.6 to set up the equipment. If the status display shows “OK” the installation Is suitable. If OK is not displayed, relocate the antenna.

1-6

Image 16

Contents THD Satellite Compass 00014854802 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures Word to the Owner of the SC-50System Configuration System configurationEquipment List Standard supplyTHD Specifications of THD Satellite Compass SC-50Coating Color Installing the antenna above superstructures Installing the antenna below superstructuresMounting Considerations Antenna unitHorizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitAntenna unit SC-303 Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitHow to orient the antenna elements Antenna unit SC-603Mounting Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unit top viewWelding the antenna unit Fastening the antenna cable Antenna elementBulkhead mount Installing the Processor UnitBulkhead mount Deck mount Processor unit orientation, deck mountingInstallation on the underside of a desk Installation of processor unit on the underside of a deskProcessor Unit, rear view Mounting on underside of deskDesktop, overhead mounting Installing the Display UnitFlush mount Flush mount S kit Type OP20-17, Code No Flush mount SFlush mount S Wiring WiringHow to install the optional antenna cable set Sectional view of coaxial cable DPYC-1.5How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status Initial SettingsSatellite tracking status display Choosing mounting method Installation setup menuMain menu Connection of External Equipment General wiringProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationThis page intentionally left blank Controls Display unitPanel Illumination, Display Contrast Turning the Power On/OffProcessor unit Choosing a Display Description of displaysHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Speed display SOG/STW displayAlarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Data OUT1 menu, sentences Baud rate optionsIEC, Nmea version options Tx interval optionsHeading talker options Output sentence limitation Sentence and maximum number of charactersLog pulse Log pulse optionsSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation Others menu Others MenuHDG Restoration options Trip Menu Trip menuResetting Distance Run Choosing External Heading Source for BackupReset Distance prompt Heading setup menuMAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence ROM, RAM, KEY TestDiagnostic test2 TEST2 displayAlarm options Diagnostic test3TEST3 menu Program Number Clearing DataProgram number display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRMenu Tree AP-1Digital Interface Schematic diagrams AP-3Data Data OutData sentences AP-4AP-5 GNS Gnns fix dataAP-6 VBW Dual ground/water speedAP-7 VLW Distance travelled through the waterInput/Output Ports Port Terminal Name Signal Remarks LabelAP-8 AP-9 HdthdghdmAP-10 Parts List and Parts LocationProcessor Unit, cover removed AP-11 Display Unit, cover openedGeodetic Chart Codes AP-12Principle of Satellite Compass AP-13What is WAAS? AP-14ＰａｃｋｉｎｇＬｉｓｔ Page 工事材料表 20AT-X-9401 Installation Materials SC-502-J/E 20AY-X-9404 SC-501-J/E 20AY-X-9401 Spare Parts List for ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Page 表示部 Index IN-1