Furuno Sc 50 manual Fabrication of cables, Cable Sectional view, fabrication

Page 33

1. INSTALLATION

1.7.2Fabrication of cables

Cable

 

Sectional view, fabrication

Power

 

50

50

cable

 

 

 

DPCY-1.5

Armor

Sheath

Armor

(or

Sheath

 

 

equivalent)

 

 

Cut the sheath.

φ = 11.7 mm

 

 

 

 

15

Conductor

 

6

 

 

S = 1.5 mm 2

 

 

φ = 1.56 mm

 

 

SECTIONAL VIEW

Crimp-on lug Vinyl tape

Lay in clamp

 

FV1.25-5

where paint

 

FABRICATION

was removed.

Cable for

 

80

3

IEC 61162

Armor

 

 

format

Sheath

Braided shield

Armor

equipment

 

 

 

 

 

(JIS cable

Shield

 

 

TTYCS-1

φ = 10.1 mm Conductor

 

 

or

S = 0.75 mm2

8

Twist and cut.

φ = 1.11 mm

 

equivalent)

SECTIONAL VIEW (TTYCS-1)

 

 

 

 

 

Cable for

6

Four cores on TTYCS-1Q

 

 

 

Solder

 

AD-10

Armor

 

 

format

Sheath

Ground wire (70)

 

 

 

 

equipment

 

 

 

Remove paint by

Shield

 

 

40 mm, clamp this

((JIS cable

15

10

φ = 11.3 mm

part in cable clamp.

 

 

 

TTYCS-1Q

Conductor

 

 

 

S = 0.75 mm2

 

 

 

or

φ = 1.11 mm

 

Vinyl tape

 

 

 

 

 

 

 

 

equivalent)

SECTIONAL VIEW (TTYCS-1Q)

 

FABRICATION

 

 

 

 

 

 

 

NOTE ON WIRING

 

 

 

1) Ground both this unit

 

 

and external equipment.

2)Fabricate braided shield of external equipment as follows:

-IEC 61162-1 input, AD-10 input (photo coupler): Connect to FG(frame ground).

-IEC 61162-2 input (RS-422/485): Connect to SG(signal ground).

Note: The power section of this equipment is insulated so the potential of SG and FG are the same. If the shielding is not properly done, the data output IC may be damaged.

1-23

Image 33
Contents THD Satellite Compass 00014854802 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingWord to the Owner of the SC-50 FeaturesSystem configuration System ConfigurationStandard supply Equipment ListSC-50 THD Specifications of THD Satellite CompassCoating Color Installing the antenna below superstructures Installing the antenna above superstructuresMounting Considerations Antenna unitMast diameter Separation distance minimum Horizontal separation between antenna and mastsAntenna and field of view Display unit, processor unit Example of antenna installed below superstructuresInstalling the Antenna Unit Mounting dimensions for antenna, orienting the antennaAntenna unit SC-303 How to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsMounting Antenna unit SC-603Fixing antenna unit to pedestal Orienting the antenna unit top view Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableInstalling the Processor Unit Bulkhead mountBulkhead mount Processor unit orientation, deck mounting Deck mountInstallation of processor unit on the underside of a desk Installation on the underside of a deskProcessor Unit, rear view Mounting on underside of deskInstalling the Display Unit Desktop, overhead mountingFlush mount Flush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring WiringSectional view of coaxial cable DPYC-1.5 How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Confirming satellite statusSatellite tracking status display Installation setup menu Choosing mounting methodMain menu General wiring Connection of External EquipmentProcessor unit, cover opened Cable Sectional view, fabrication Fabrication of cablesThis page intentionally left blank Display unit ControlsTurning the Power On/Off Panel Illumination, Display ContrastProcessor unit Description of displays Choosing a DisplayHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display SOG/STW display Speed displayAlarm menu Alarm SetupDgps alarm options Buzzer optionsSatellite status display Confirming Satellite StatusGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Baud rate options Data OUT1 menu, sentencesTx interval options IEC, Nmea version optionsHeading talker options Sentence and maximum number of characters Output sentence limitationLog pulse options Log pulseSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode Position fix mode options WAAS/DGPS SetupWAAS/DGPS menu Waas Search optionsProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation Others Menu Others menuHDG Restoration options Trip menu Trip MenuChoosing External Heading Source for Backup Resetting Distance RunReset Distance prompt Heading setup menuPreventive Maintenance MAINTENANCE, TroubleshootingTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostic test1 DiagnosticsTest menu options Test start promptROM, RAM, KEY Test Diagnostic test sequenceTEST2 display Diagnostic test2Diagnostic test3 Alarm optionsTEST3 menu Clearing Data Program NumberProgram number display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryPrompt for exchanging battery Prompt for turning off the powerError Messages Replacement of FuseError Message Meaning Remedy Message displayData ERR Error messages con’t from previousAP-1 Menu TreeDigital Interface AP-3 Schematic diagramsData Data OutAP-4 Data sentencesGNS Gnns fix data AP-5VBW Dual ground/water speed AP-6VLW Distance travelled through the water AP-7Port Terminal Name Signal Remarks Label Input/Output PortsAP-8 Hdthdghdm AP-9Parts List and Parts Location AP-10Processor Unit, cover removed Display Unit, cover opened AP-11AP-12 Geodetic Chart CodesAP-13 Principle of Satellite CompassAP-14 What is WAAS?Packing List Page 工事材料表 20AT-X-9401 Installation Materials SC-502-J/E 20AY-X-9404 SC-501-J/E 20AY-X-9401 Spare Parts List for フラッシュマウントキット 20AY-X-9403 Hatai Page Page Page Page Page 表示部 IN-1 Index