Furuno FR-2135S manual Separate type control head kit Type OP03-151, No

Page 19

Separate type control head kit (Type: OP03-151, No.: 008-485-530)

Name	Type	Qty	Code no.	Remarks

Cable Assy.	UL246SB20P/1P	1	000-140-812	10 m, 03S9422

Rubber Feet	SJ-5003	4	000-801-787	w/tape

Monitor Front Cover	03-255-1361	1	100-263-340

KB Fixing Plate	03-144-1691	1	100-263-940

Handle Plate	03-144-1632	1	100-268-041

Dust cover KB	03-144-1693	1	100-271-760

Screw	M4x10	3	000-881-446

Label	86-003-1011	1	100-236-230

Nonship Rubber	03-144-1694	1	100-271-760

Display unit modification procedure

1.Raise the monitor unit referring to procedure for tabletop mounting on page 1- 8.

2.Unplug two connectors from the control head cable (P412 from MOTHER Board and J583 and unfasten two earth wires.

PTU COVER
J583	Control Head
J583	Cable
Earth Wire
J418
MB 03P9251
P412
INT
03P9252

Figure 1-13 Display unit, inside view

3. Lower the monitor.

1-11

Image 19

Contents Back 00080839301 Safety Instructions Use only the specified power cable Table of Contents Standard Supply Equipment ListsName Type Code No Qty Remarks Optional EquipmentSystem Configuration Mounting considerations Scanner UnitExample Installation precaution for S-band scanner unitAttachment of lifting fixtures and collar How to lift scanner unitScanner unit assembling Scanner unit assembling procedureFastening the scanner unit to the mounting platform Installation of reinforcement ribsMounting of scanner unit Tabletop mounting Mounting procedureDisplay Unit Before mounting the display unitStay 10 Setting catch to hole in stay Separating the control head Console type mountingSeparate type control head kit Type OP03-151, No Display unit modification procedure14 Detaching the control head Connection of display unit to control head Control head modification procedureAttachment of hood 16 How to attach KB fixing platePower Supply Unit This page is intentionally left blank Fabricating the power cable DPYCY-3.5 JIS cable WiringLeading in cables to the display unit Cable fed from back of display unit default methodCables fed from bottom of display unit console mount Cable fed from outside display unitRemove ConnectionsConnectors on the INT Board Connectors on the INT BoardHOW to Attach NH Connector to Signal Cable How to attach NH connector10 Scanner unit, port side view 11 Fabricating the signal cable S03-74 Fabricating signal cable S03-7413 Scanner unit, rear view 15 Fabrication of coaxial cable When the de-icer is installed Changing AC Power Specification of Display Unit18 Power supply unit PSU-004 Restoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal LevelPicture appears Deviated counterclockwise Heading AlignmentSuppressing Main Bang Adjusting Sweep TimingConfirming Magnetron Heater Voltage Antenna switch in tuning compartmentScanner unit, stern side view Initial Setting MenusPress Radar Menu 0 0 0 Initial SETTING1 menuInitial SETTING3 menu Initial SETTING2 menuOWN Ship Information menu Initial SETTING4 menuGyro Converter GC-8 Installation and connection of the Gyro Converter BoardINT Board DIP switch, jumper wire settings Connection of external power supplyDefault setting Gyrocompass type Setting method 1 by gyrocompass specificationsJP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompassSW1 Setting the heading readout on the radar displayARP Board ARP-26 Installation of the ARP boardARP Board 18P9002B ARP board adjustmentARP Board ARP-26 Final checkTable top/console type RP Board RP-2610 Display pedestal Necessary parts RP-26-Z-2E Code no Separate type control head13 Display pedestal, front view Necessary parts PM-50 and OP03-150 Code no Performance Monitor PM-50Procedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page