Furuno FR-2135S manual Connections, Remove

Page 28

Connections

Open the display unit and fix it with the stay. (For procedure see page 1-6.) Re- move the shield cover from the INT Board. Connect signal, power, gyro and log cables as shown on the next page. Optional equipment are connected to the INT Board. Be sure to ground the display unit.

Ship's

Gyro

Scanner Log

Fasten shield here.Unit

(Tabletop type)Ground terminal (Tabletop type)

PTU BOARD 03P9245

			Terminal
			board
			Fasten shields
			here together.
			(Console type)
	Connect coax		POWER switch
	Connect coax		(for maintenance,
	MOTHER BOARD cable here.		(for maintenance,
	MOTHER BOARD cable here.		always ON)
	03P9251	DJ1
		J5	Fasten TX-HV
	J448	J5	line to #1 termanal.
	J448		To fasten;
		J4	1. Slide terminal.
		J4	2. Lift terminal to
			2. Lift terminal to
			remove.
	INT BOARD	GYRO CONVERTER
	03P9252	BOARD 64P1106

J442

J443

J444

J463

J457

J458

J453

J451

J452

J450

J454

J455

J466

J462

J456

J445

J448

J446

J467

J449

J465

Fix the DJ1 connector with teo M3x8 screw )supplied).

Location of connectors on the INT Board. See next page for connector description.

CAUTION

Ground the equipment to prevent electrical shock and mutual interference.

Bind the cables so as not to pinch them between the monitor and mounting base. Take special care with the high voltage line.

Figure 2-5 Display unit, inside view

2-4

Image 28

Contents Back 00080839301 Safety Instructions Use only the specified power cable Table of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No Qty RemarksSystem Configuration Scanner Unit Mounting considerationsInstallation precaution for S-band scanner unit ExampleHow to lift scanner unit Attachment of lifting fixtures and collarScanner unit assembling procedure Scanner unit assemblingInstallation of reinforcement ribs Fastening the scanner unit to the mounting platformMounting of scanner unit Mounting procedure Display UnitBefore mounting the display unit Tabletop mountingStay 10 Setting catch to hole in stay Console type mounting Separating the control headDisplay unit modification procedure Separate type control head kit Type OP03-151, No14 Detaching the control head Control head modification procedure Connection of display unit to control head16 How to attach KB fixing plate Attachment of hoodPower Supply Unit This page is intentionally left blank Wiring Fabricating the power cable DPYCY-3.5 JIS cableCable fed from back of display unit default method Leading in cables to the display unitCable fed from outside display unit Cables fed from bottom of display unit console mountConnections RemoveConnectors on the INT Board Connectors on the INT BoardHow to attach NH connector HOW to Attach NH Connector to Signal Cable10 Scanner unit, port side view Fabricating signal cable S03-74 11 Fabricating the signal cable S03-7413 Scanner unit, rear view 15 Fabrication of coaxial cable Changing AC Power Specification of Display Unit When the de-icer is installed18 Power supply unit PSU-004 Tuning Initialization Accessing Menus for Initialization and AdjustmentAdjusting Video Signal Level Restoring default settingsHeading Alignment Picture appears Deviated counterclockwiseAdjusting Sweep Timing Suppressing Main BangAntenna switch in tuning compartment Confirming Magnetron Heater VoltageInitial Setting Menus Scanner unit, stern side viewInitial SETTING1 menu Press Radar Menu 0 0 0Initial SETTING2 menu Initial SETTING3 menuInitial SETTING4 menu OWN Ship Information menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8INT Board DIP switch, jumper wire settings Connection of external power supplyDefault setting Setting method 1 by gyrocompass specifications Gyrocompass typeSetting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5Setting the heading readout on the radar display SW1Installation of the ARP board ARP Board ARP-26ARP board adjustment ARP Board 18P9002BFinal check ARP Board ARP-26RP Board RP-26 Table top/console type10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no13 Display pedestal, front view Performance Monitor PM-50 Necessary parts PM-50 and OP03-150 Code noProcedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page