Furuno FAR-2167DS-D, FAR-2167DS-BB Power supply unit, Power Fuse Jumper connector P8

Page 41

Power supply unit

Refer to the illustration and table below to add (or remove) jumper connector P8 from the TX-HV Board (03P9350) and change fuse.

After completing jumper and fuse arrangements, adjust the overvoltage detection circuit, using a variable transformer.

Note: When switching from 220 VAC to 100 VAC, construct a jumper connector locally, referring to the illustration below. (VH6 connector housing is to be plugged into J8.)

Power	Fuse	Jumper connector P8

100 VAC	5A	Required

220 VAC	3A	Unnecessary

Unfasten four screws and remove cover for TX-HV Board.

P8/J8

6 5 4 3 2 1

Jumper connector (VH6P)

CR23

R21

TX-HV Board

Fuse

TB1

2-17

Image 41

Contents Installation manual 00014869014 Safety Instructions Use only the specified power cables Iii System ConfigurationName Type Code No Qty Remarks Standard supplyName Type Code No Remarks Optional equipmentThis page is intentionally left blank Mounting considerations Antenna UnitSiting MountingMounting precaution for S-band antenna unit Installation precaution for S-band antenna unitAssembling the antenna unit Assembling the antenna unitAttachment of lifting fixtures, collar and ropes How to hoist the antenna unitFastening the antenna unit to the mounting platform Installation of reinforcement ribsMounting the antenna unit Flush mounting Mounting procedureMonitor Unit Desktop mounting Contents of desktop mounting kit FP03-09820Attaching hand grips Fixing with KB keyboard fixing plate Control UnitFixing without KB fixing plate Mounting dimensions for control unit RCU-014Mounting dimensions for control unit RCU-015/RCU-016 Name Type Qty Contents of flush mount kit for RCU-014/015/016Control unit RCU-014, inside view Connecting RCU-016 in series with RCU-014Changing cable entrance on control unit RCU-015/RCU-016 Changing the cable entrance on control unit RCU-015/RCU-016Processor Unit Mounting dimensions for processor unitMounting dimensions for power supply unit Power Supply UnitWiring Overview WiringAntenna unit, front view Fabricating signal cable RW-9600 and HV cable TYPCY-1.5Fabricating signal cable RW-9600 Armor Gasket Signal cable Flat washer Flat washer Gland nut How to fabricate HV cable TYPCY-1.5 How to wire Wago connectorHow to fabricate power cable TYPCY-2.5 Fabricating the power cable TYPCY-2.5Antenna unit, left-side view Passing flat washer, etc. onto HV cableFabricating power cable DPYC-2.5 Fabricating the power cable DPYC-2.5Monitor Unit for FAR-2167DS Monitor unit MU-201CR, rear viewProcessor Unit Cable XH10P-W-6P L=20/30M Connection of cablesProcessor unit, rear view Location of connectors inside the processor unit Location of connectorsPower cable TPYC-1.5 Signal cable RW-9600 Between antenna unit and processor unitPort Conventional remote display FAR-2167DS Connection of Sub-displayTerminal TB1 cable DPYC-2.5 Power supply unit, inside viewFabricating cable connected to terminal TB1, TB2, TB3 Armor Power supply Fuse Jumper connector P108 Changing AC Power SpecificationProcessor unit Processor unit, inside viewHow to adjust the overvoltage detection circuit Power Fuse Jumper connector P8 Power supply unitHow to adjust the overvoltage detection circuit Initializing Tuning AdjustmentsHeading alignment Heading AlignmentFor Control Unit RCU-015 For Control Unit RCU-014Initialize menu Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Examples of correct and incorrect sweep timings Adjusting Sweep TimingSuppressing Main Bang Echo menu setting Other SettingsANT SW and ANT Stopped Scanner menuBlind Sector 1 and Blind Sector On Time and TX Time Installation menuRadar no and Radar Posn GPS 1 ANT Posn and GPS 2 ANT Posn OWN Ship Info menuLENGTH/WIDTH, Scanner Posn and SUB Scanner Posn ARP-related menus Arpa Preset menuARP W/O Gyro Not shown on IMO radar ANT Select Other menu Other menuEAV w/o Gyro This page intentionally left blank Gyro Converter GC-10 Installing the Gyro Converter boardFixing Gyro Converter board inside the processor unit Wiring Wago connector Connecting connector assemblies inside processor unitAttaching plastic cover for Gyro Converter board DIP switch, jumper wire settings Connection of external power supplyDefault setting Connection of external power supply to Gyro Converter boardJP1 JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompassGyro Converter board 64P1106HDG menu Setting the heading readout on the radar displayMemory Card Interface Unit Flush mounting dimensions for memory card interface unitDesktop mount ConnectionsOne memory card if unit and one processor unit One memory card if unit and multiple processor unitsType Code No Contents DVI-RGB Conversion Kit How to wire the DVI-RBG conversion boardProcessor unit bottom chassis Processor unit, side viewConnecting wires to the housing DVI-RGB BNC Connector ConverterOutput Data Specifications Contents RemarksInput IEC 61162 output sentence IEC 61162 input sentence and prioritySentence and order of priority SentenceＰａｃｋｉｎｇＬｉｓｔ 1 SN30AF/SN36AF 70+6 000-157-497-10 工事材料表 000-155-826-10 PSU-006 AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Interconnection Diagram