Furuno FAR-2167DS-D DVI-RGB Conversion Kit, How to wire the DVI-RBG conversion board

Page 69

4.3 DVI-RGB Conversion Kit

This information provides the procedure necessary for the installation of the DVI-RGB conversion kit. This kit is installed in the processor unit to enable connection of an RGB monitor or VDR (Voyage Data Recorder).

Name: DVI-RGB conversion kit

Type: OP03-180-2

Code no.: 008-536-070

See packing list for contents. Refer to the figure below for modification.

M3x8 6 pcs

J4

DVI-RGB CONVERSION board (SLB-FRN4-A)

DVI cable

J9 J3

(10 pin)

(6 pin)

J615

03-2092

03-2094

03-2093

03P9342 board

RGB-BUFF board

(03P9229B)

D-sub 15P

 

Spacer SQ-35 6 pcs

Fixing holes

M3x8

 

4 pcs

J3

J1

(3 pin)

(13 pin)

 

Spring washer

Boss

To external monitor or BNC connector converter (see page 4-15).

J2

Female

 

 

RGB Cable

 

(User supply)

Ferrite core

Clamp copper tape section by cable clamp.

Ferrite core side: Connect to DVI-D port on the upper part of the processor unit.

How to wire the DVI-RBG conversion board

4-13

Image 69
Contents Installation manual 00014869014 Safety Instructions Use only the specified power cables Iii System ConfigurationName Type Code No Qty Remarks Standard supplyName Type Code No Remarks Optional equipmentThis page is intentionally left blank Mounting considerations Antenna UnitSiting MountingMounting precaution for S-band antenna unit Installation precaution for S-band antenna unitAssembling the antenna unit Assembling the antenna unitAttachment of lifting fixtures, collar and ropes How to hoist the antenna unitFastening the antenna unit to the mounting platform Installation of reinforcement ribsMounting the antenna unit Mounting procedure Monitor UnitFlush mounting Desktop mounting Contents of desktop mounting kit FP03-09820Attaching hand grips Fixing with KB keyboard fixing plate Control UnitMounting dimensions for control unit RCU-014 Mounting dimensions for control unit RCU-015/RCU-016Fixing without KB fixing plate Name Type Qty Contents of flush mount kit for RCU-014/015/016Control unit RCU-014, inside view Connecting RCU-016 in series with RCU-014Changing cable entrance on control unit RCU-015/RCU-016 Changing the cable entrance on control unit RCU-015/RCU-016Processor Unit Mounting dimensions for processor unitMounting dimensions for power supply unit Power Supply UnitWiring Overview WiringFabricating signal cable RW-9600 and HV cable TYPCY-1.5 Fabricating signal cable RW-9600Antenna unit, front view Armor Gasket Signal cable Flat washer Flat washer Gland nut How to fabricate HV cable TYPCY-1.5 How to wire Wago connectorHow to fabricate power cable TYPCY-2.5 Fabricating the power cable TYPCY-2.5Antenna unit, left-side view Passing flat washer, etc. onto HV cableFabricating power cable DPYC-2.5 Fabricating the power cable DPYC-2.5Monitor Unit for FAR-2167DS Monitor unit MU-201CR, rear viewProcessor Unit Connection of cables Processor unit, rear viewCable XH10P-W-6P L=20/30M Location of connectors inside the processor unit Location of connectorsPower cable TPYC-1.5 Signal cable RW-9600 Between antenna unit and processor unitPort Conventional remote display FAR-2167DS Connection of Sub-displayPower supply unit, inside view Fabricating cable connected to terminal TB1, TB2, TB3Terminal TB1 cable DPYC-2.5 Armor Power supply Fuse Jumper connector P108 Changing AC Power SpecificationProcessor unit Processor unit, inside viewHow to adjust the overvoltage detection circuit Power Fuse Jumper connector P8 Power supply unitHow to adjust the overvoltage detection circuit Initializing Tuning AdjustmentsHeading alignment Heading AlignmentFor Control Unit RCU-015 For Control Unit RCU-014Initialize menu Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Examples of correct and incorrect sweep timings Adjusting Sweep TimingSuppressing Main Bang Echo menu setting Other SettingsScanner menu Blind Sector 1 and Blind SectorANT SW and ANT Stopped Installation menu Radar no and Radar PosnOn Time and TX Time OWN Ship Info menu LENGTH/WIDTH, Scanner Posn and SUB Scanner PosnGPS 1 ANT Posn and GPS 2 ANT Posn Arpa Preset menu ARP W/O Gyro Not shown on IMO radarARP-related menus ANT Select Other menu EAV w/o GyroOther menu This page intentionally left blank Gyro Converter GC-10 Installing the Gyro Converter boardFixing Gyro Converter board inside the processor unit Wiring Wago connector Connecting connector assemblies inside processor unitAttaching plastic cover for Gyro Converter board DIP switch, jumper wire settings Connection of external power supplyDefault setting Connection of external power supply to Gyro Converter boardJP1 JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompassGyro Converter board 64P1106HDG menu Setting the heading readout on the radar displayMemory Card Interface Unit Flush mounting dimensions for memory card interface unitDesktop mount ConnectionsOne memory card if unit and one processor unit One memory card if unit and multiple processor unitsType Code No Contents DVI-RGB Conversion Kit How to wire the DVI-RBG conversion boardProcessor unit bottom chassis Processor unit, side viewConnecting wires to the housing DVI-RGB BNC Connector ConverterData Specifications Contents Remarks InputOutput IEC 61162 output sentence IEC 61162 input sentence and prioritySentence and order of priority SentencePacking List 1 SN30AF/SN36AF 70+6 000-157-497-10 工事材料表 000-155-826-10 PSU-006 AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Interconnection Diagram