Furuno FAR-2157-BB, FAR-2157-D installation manual Monitor Unit, Mounting procedure, Flush mounting

Page 15

1.2 Monitor Unit

The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional accessories).

The FAR-2157-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally. Rec- ommended monitor: SXGA (1280×1024), aspect ratio 5:4.

For MU-190, see the applicable Operator’s Manual.

Mounting considerations

When selecting a mounting location, keep in mind the following points:

Select a location where the screen can be viewed conveniently while facing the bow.

Locate the unit out of direct sunlight and away from heat sources because of heat that can build up inside the cabinet.

Locate the unit away from places subject to water splash and rain.

Leave sufficient space on the sides and rear of the unit to facilitate maintenance, referring to the outline drawing for maintenance space.

The monitor unit will give interference to a magnetic compass if it is placed too close to the com- pass. Observe the compass safe distances on page ii to prevent interference to the compass.

Mounting procedure

Flush mounting

Follow the procedure below to mount the monitor unit in a console.

1.Make a cutout in the mounting location referring to the outline drawing shown below.

2.Set the monitor unit to the hole and fix it with four self-tapping screws (6×30).

3.Attach panel hooks near the fixing holes (upper part). See next page. These are used to pull out the monitor unit from the panel for servicing.

4.Attach four panel covers to the fixing holes.

506

1

4-FIXING HOLES

 

 

 

 

 

 

 

 

 

 

 

1

420

 

1

454

 

 

296

 

296

 

 

 

 

 

(79)

 

 

490

 

506

1

4-φ8

 

 

 

534

 

FIXING HOLES

80

 

 

 

 

 

30

Mounting dimensions for flush mounting the monitor unit

1-7

Image 15
Contents Installation manual 00014869214 Safety Instructions Use only the specified power cables Iii System ConfigurationName Type Standard supplyOptional equipment Name Type Code No Qty RemarksDVI-RGB Name Type Code No RemarksThis page is intentionally left blank Mounting Antenna UnitMounting considerations SitingAssembling the antenna unit How to coat waveguide flange with silicon rubberName Type Qty How to attach hoisting ropes to antenna unit How to hoist antenna unitFastening antenna unit to the mounting platform Coat with anticorrosive sealant How to mount the antenna unitMounting procedure Monitor UnitFlush mounting Desktop mounting Contents of desktop mounting kit FP03-09820Attaching hand grips Fixing with KB keyboard fixing plate Control UnitMounting dimensions for control unit RCU-014 Mounting dimensions for control unit RCU-015/RCU-016Fixing without KB fixing plate Contents of flush mount kit for RCU-014/015/016 Control unit RCU-014, inside view Connecting RCU-016 in series with RCU-014Changing cable entrance on control unit RCU-015/RCU-016 Changing the cable entrance on control unit RCU-015/RCU-016Processor Unit Mounting dimensions for processor unitMounting dimensions for power supply unit Power Supply UnitWiring Overview WiringFabricating signal cable RW-9600 Fabricating signal cable RW-9600Antenna unit, front view TB801 PCB 03P9436 Cable gland for signal cable RW-9600 Procedure How to wire Wago connectorHow to fasten coaxial conductor Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5 How to fabricate HV cable TYPCY-1.5Passing flat washer, etc. onto HV cable Passing flat washer, etc. onto power cable How to fabricate power cable TYPCY-2.5Fabricating power cable DPYC-2.5 Fabricating the power cable DPYC-2.5Fabricating power cable DPYC-2.5 Cable XH10P-W-5P-A L=10/20/30M Connection of cablesProcessor unit, rear view Cable XH10P-W-6P L=20/30MLocation of connectors inside the processor unit Location of connectorsPower cable TPYC-1.5 Signal cable RW-9600 Between antenna unit and processor unitPort Conventional remote display FAR-2157 Connection of Sub-displayPower supply unit, inside view Fabricating cable connected to terminal TB1, TB2, TB3Terminal TB1 cable DPYC-2.5 Armor Processor unit, inside view Changing AC Power SpecificationPower supply Fuse Jumper connector P108 Processor unitHow to adjust the overvoltage detection circuit Power Fuse Jumper connector P8 Power supply unitInitializing Tuning AdjustmentsHeading alignment Heading AlignmentEcho ADJ menu For Control Unit RCU-014For Control Unit RCU-015 Initialize menuHow to access the Initialize Menu with Control Unit RCU-015 Examples of correct and incorrect sweep timings Adjusting Sweep TimingSuppressing Main Bang Echo menu setting Other SettingsScanner menu Blind Sector 1 and Blind SectorANT SW and ANT Stopped Installation menu Radar no and Radar PosnOn Time and TX Time OWN Ship Info menu LENGTH/WIDTH, Scanner Posn and SUB Scanner PosnGPS 1 ANT Posn and GPS 2 ANT Posn Arpa Preset menu ARP W/O Gyro Not shown on IMO radarARP-related menus ANT Select Other menu EAV w/o GyroOther menu This page intentionally left blank Gyro Converter GC-10 Installing the Gyro Converter boardFixing Gyro Converter board inside the processor unit Wiring Wago connector Connecting connector assemblies inside processor unitAttaching plastic cover for Gyro Converter board Connection of external power supply to Gyro Converter board Connection of external power supplyDIP switch, jumper wire settings Default settingJP1 JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompassGyro Converter board 64P1106HDG menu Setting the heading readout on the radar displayMemory Card Interface Unit Flush mounting dimensions for memory card interface unitOne memory card if unit and multiple processor units ConnectionsDesktop mount One memory card if unit and one processor unitType Code No Contents DVI-RGB Conversion Kit How to wire the DVI-RBG conversion boardProcessor unit bottom chassis Processor unit, side viewConnecting wires to the housing DVI-RGB BNC Connector ConverterData Specifications Contents Remarks InputOutput Sentence IEC 61162 input sentence and priorityIEC 61162 output sentence Sentence and order of priorityList #  70+6 000-157-497-10 工事材料表 000-155-826-10 Packing List AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Marine RADAR/ARPA