Furuno FAR-2157-D, FAR-2157-BB Fabricating signal cable RW-9600, Antenna unit, front view

Page 26

2.2 Antenna Unit

Gland for HV cable (TPYCY-1.5)

PCB 03P9436

Cover

Antenna safety switch

PCB 03P9435

Terminal strip

Cover

Gland for power cable (TPYCY-2.5) Ground terminal

Gland for signal cable (RW-9600)

Antenna unit, front view

Fabricating signal cable RW-9600

1.Use a ratchet or box wrench (diagonal 13 mm) to open port- and starboard-side covers on the antenna unit.

2.Unfasten the gland nut for the signal cable and remove the gasket, flat washers (3 pcs.) and gland cap. (The gland cap may be discarded.)

3.Fabricate the signal cable as follows:

a)Remove the vinyl sheath, armor and sheath by the amounts shown in the figure below.

b)Unravel the shield to expose cores.

c)Shorten cores (except coax) considering their locations on the terminal inside the antenna unit.

d)Shorten the shield, leaving 300 mm. Attach crimp-on-lug (FV5.5-4, yellow, φ4) to shield.

e)Remove the sheath of cores by 6 mm.

f)Unravel armor.

g)Fix vinyl wire, coaxial cable and shield by taping the shield with vinyl tape at the location shown below.

Vinyl

Armor

Sheath

Shield

sheath

 

 

 

 

 

20 mm

 

550 mm

 

 

5 mm

 

 

 

 

500 mm

 

 

 

 

Coaxial cable

 

Shield

 

Vinyl wire

 

 

 

 

 

Taping

 

 

6

 

 

 

 

 

 

 

 

14 5 9

 

Unravel armor.

 

 

 

Core

 

 

 

 

 

Shield

 

Fold back shield.

 

 

Coaxial cable

 

Crimp-on lug

 

 

 

Fabricating signal cable RW-9600

2-2

Image 26
Contents Installation manual 00014869214 Safety Instructions Use only the specified power cables System Configuration IiiName Type Code No Qty Remarks Standard supplyOptional equipment Name TypeName Type Code No Remarks DVI-RGBThis page is intentionally left blank Siting Antenna UnitMounting considerations MountingHow to coat waveguide flange with silicon rubber Assembling the antenna unitName Type Qty How to hoist antenna unit How to attach hoisting ropes to antenna unitFastening antenna unit to the mounting platform How to mount the antenna unit Coat with anticorrosive sealantFlush mounting Mounting procedureMonitor Unit Contents of desktop mounting kit FP03-09820 Desktop mountingAttaching hand grips Control Unit Fixing with KB keyboard fixing plateFixing without KB fixing plate Mounting dimensions for control unit RCU-014Mounting dimensions for control unit RCU-015/RCU-016 Contents of flush mount kit for RCU-014/015/016 Connecting RCU-016 in series with RCU-014 Control unit RCU-014, inside viewChanging the cable entrance on control unit RCU-015/RCU-016 Changing cable entrance on control unit RCU-015/RCU-016Mounting dimensions for processor unit Processor UnitPower Supply Unit Mounting dimensions for power supply unitWiring Wiring OverviewAntenna unit, front view Fabricating signal cable RW-9600Fabricating signal cable RW-9600 TB801 PCB 03P9436 Cable gland for signal cable RW-9600 How to wire Wago connector ProcedureHow to fasten coaxial conductor Passing flat washer, etc. onto HV cable Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5How to fabricate HV cable TYPCY-1.5 How to fabricate power cable TYPCY-2.5 Passing flat washer, etc. onto power cableFabricating the power cable DPYC-2.5 Fabricating power cable DPYC-2.5Fabricating power cable DPYC-2.5 Cable XH10P-W-6P L=20/30M Connection of cablesProcessor unit, rear view Cable XH10P-W-5P-A L=10/20/30MLocation of connectors Location of connectors inside the processor unitSignal cable RW-9600 Between antenna unit and processor unit Power cable TPYC-1.5Connection of Sub-display Port Conventional remote display FAR-2157Terminal TB1 cable DPYC-2.5 Power supply unit, inside viewFabricating cable connected to terminal TB1, TB2, TB3 Armor Processor unit Changing AC Power SpecificationPower supply Fuse Jumper connector P108 Processor unit, inside viewHow to adjust the overvoltage detection circuit Power supply unit Power Fuse Jumper connector P8Adjustments Initializing TuningHeading Alignment Heading alignmentInitialize menu For Control Unit RCU-014For Control Unit RCU-015 Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Adjusting Sweep Timing Examples of correct and incorrect sweep timingsSuppressing Main Bang Other Settings Echo menu settingANT SW and ANT Stopped Scanner menuBlind Sector 1 and Blind Sector On Time and TX Time Installation menuRadar no and Radar Posn GPS 1 ANT Posn and GPS 2 ANT Posn OWN Ship Info menuLENGTH/WIDTH, Scanner Posn and SUB Scanner Posn ARP-related menus Arpa Preset menuARP W/O Gyro Not shown on IMO radar ANT Select Other menu Other menuEAV w/o Gyro This page intentionally left blank Installing the Gyro Converter board Gyro Converter GC-10Fixing Gyro Converter board inside the processor unit Connecting connector assemblies inside processor unit Wiring Wago connectorAttaching plastic cover for Gyro Converter board Default setting Connection of external power supplyDIP switch, jumper wire settings Connection of external power supply to Gyro Converter boardJP1 Setting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP564P1106 Gyro Converter boardSetting the heading readout on the radar display HDG menuFlush mounting dimensions for memory card interface unit Memory Card Interface UnitOne memory card if unit and one processor unit ConnectionsDesktop mount One memory card if unit and multiple processor unitsType Code No Contents How to wire the DVI-RBG conversion board DVI-RGB Conversion KitProcessor unit, side view Processor unit bottom chassisConnecting wires to the housing BNC Connector Converter DVI-RGBOutput Data Specifications Contents RemarksInput Sentence and order of priority IEC 61162 input sentence and priorityIEC 61162 output sentence SentenceList #  70+6 000-157-497-10 工事材料表 000-155-826-10 Packing List AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Marine RADAR/ARPA