Furuno FAR-2157-D, FAR-2157-BB installation manual BNC Connector Converter, Dvi-Rgb

Page 72

4.4 BNC Connector Converter

To connect the FURUNO Voyage Data Recorder VR-5000 to this radar, the DVI-RGB conversion kit (mentioned at previous paragraph) and the BNC connector converter are required. Also VGA cable (between the processor unit and the BNC connector converter) and five 75 ohm coaxial cables (between the BNC connector converter and VR-5000) are required.

FAR-2157(-BB)

PROCESSOR UNIT

	DVI-RGB		VGA cable

		D-sub 15P	D-sub 15P
	Conversion kit	D-sub 15P	D-sub 15P
	Conversion kit	Female	Male

BNC CONNECTOR CONVERTER R DSUB-BNC-1 G

B

H

V

75 W coax. cable

VR-5000

VD1 DATA COLLECTING

RUNIT

G

B

HS

VS

Connecting VR-5000 to FAR-2157(-BB) via BNC connector converter

BNC connnector converter

4-16

Image 72

Contents Installation manual 00014869214 Safety Instructions Use only the specified power cables System Configuration IiiStandard supply Optional equipmentName Type Code No Qty Remarks Name TypeName Type Code No Remarks DVI-RGBThis page is intentionally left blank Antenna Unit Mounting considerationsSiting MountingHow to coat waveguide flange with silicon rubber Assembling the antenna unitName Type Qty How to hoist antenna unit How to attach hoisting ropes to antenna unitFastening antenna unit to the mounting platform How to mount the antenna unit Coat with anticorrosive sealantMounting procedure Monitor UnitFlush mounting Contents of desktop mounting kit FP03-09820 Desktop mountingAttaching hand grips Control Unit Fixing with KB keyboard fixing plateMounting dimensions for control unit RCU-014 Mounting dimensions for control unit RCU-015/RCU-016Fixing without KB fixing plate Contents of flush mount kit for RCU-014/015/016 Connecting RCU-016 in series with RCU-014 Control unit RCU-014, inside viewChanging the cable entrance on control unit RCU-015/RCU-016 Changing cable entrance on control unit RCU-015/RCU-016Mounting dimensions for processor unit Processor UnitPower Supply Unit Mounting dimensions for power supply unitWiring Wiring OverviewFabricating signal cable RW-9600 Fabricating signal cable RW-9600Antenna unit, front view TB801 PCB 03P9436 Cable gland for signal cable RW-9600 How to wire Wago connector ProcedureHow to fasten coaxial conductor Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5 How to fabricate HV cable TYPCY-1.5Passing flat washer, etc. onto HV cable How to fabricate power cable TYPCY-2.5 Passing flat washer, etc. onto power cableFabricating the power cable DPYC-2.5 Fabricating power cable DPYC-2.5Fabricating power cable DPYC-2.5 Connection of cables Processor unit, rear viewCable XH10P-W-6P L=20/30M Cable XH10P-W-5P-A L=10/20/30MLocation of connectors Location of connectors inside the processor unitSignal cable RW-9600 Between antenna unit and processor unit Power cable TPYC-1.5Connection of Sub-display Port Conventional remote display FAR-2157Power supply unit, inside view Fabricating cable connected to terminal TB1, TB2, TB3Terminal TB1 cable DPYC-2.5 Armor Changing AC Power Specification Power supply Fuse Jumper connector P108Processor unit Processor unit, inside viewHow to adjust the overvoltage detection circuit Power supply unit Power Fuse Jumper connector P8Adjustments Initializing TuningHeading Alignment Heading alignmentFor Control Unit RCU-014 For Control Unit RCU-015Initialize menu Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Adjusting Sweep Timing Examples of correct and incorrect sweep timingsSuppressing Main Bang Other Settings Echo menu settingScanner menu Blind Sector 1 and Blind SectorANT SW and ANT Stopped Installation menu Radar no and Radar PosnOn Time and TX Time OWN Ship Info menu LENGTH/WIDTH, Scanner Posn and SUB Scanner PosnGPS 1 ANT Posn and GPS 2 ANT Posn Arpa Preset menu ARP W/O Gyro Not shown on IMO radarARP-related menus ANT Select Other menu EAV w/o GyroOther menu This page intentionally left blank Installing the Gyro Converter board Gyro Converter GC-10Fixing Gyro Converter board inside the processor unit Connecting connector assemblies inside processor unit Wiring Wago connectorAttaching plastic cover for Gyro Converter board Connection of external power supply DIP switch, jumper wire settingsDefault setting Connection of external power supply to Gyro Converter boardJP1 Setting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP564P1106 Gyro Converter boardSetting the heading readout on the radar display HDG menuFlush mounting dimensions for memory card interface unit Memory Card Interface UnitConnections Desktop mountOne memory card if unit and one processor unit One memory card if unit and multiple processor unitsType Code No Contents How to wire the DVI-RBG conversion board DVI-RGB Conversion KitProcessor unit, side view Processor unit bottom chassisConnecting wires to the housing BNC Connector Converter DVI-RGBData Specifications Contents Remarks InputOutput IEC 61162 input sentence and priority IEC 61162 output sentenceSentence and order of priority SentenceＬｉｓｔ # 70+6 000-157-497-10 工事材料表 000-155-826-10 ＰａｃｋｉｎｇＬｉｓｔ AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Marine RADAR/ARPA