Furuno FAR-2157-D, FAR-2157-BB Fixing Gyro Converter board inside the processor unit

Page 58

2.Fasten the GYRO CONVERTER board inside the processor unit with five washer head screws.

3.Fix connector 231-607/019-FUR (called J602) with two screws.

	Screw	GYRO CONVERTER board
	M3X8 5 pcs
		64P1106A

Screw

M2.6X10 2 pcs

Connector (231) 231-107/026-FUR

7

1

7

1

Connector (231) 231-607/019-FUR

PCB 03P9342

Fixing GYRO CONVERTER board inside the processor unit

4.Connect the GYRO CONVERTER board to the 03P9342 board with XH-PH 03-2088 connector assy. (6-14P) and NH connector assy. 03-2091.

4-2

Image 58

Contents Installation manual 00014869214 Safety Instructions Use only the specified power cables System Configuration IiiName Type Code No Qty Remarks Standard supplyOptional equipment Name TypeName Type Code No Remarks DVI-RGBThis page is intentionally left blank Siting Antenna UnitMounting considerations MountingHow to coat waveguide flange with silicon rubber Assembling the antenna unitName Type Qty How to hoist antenna unit How to attach hoisting ropes to antenna unitFastening antenna unit to the mounting platform How to mount the antenna unit Coat with anticorrosive sealantMonitor Unit Mounting procedureFlush mounting Contents of desktop mounting kit FP03-09820 Desktop mountingAttaching hand grips Control Unit Fixing with KB keyboard fixing plateMounting dimensions for control unit RCU-015/RCU-016 Mounting dimensions for control unit RCU-014Fixing without KB fixing plate Contents of flush mount kit for RCU-014/015/016 Connecting RCU-016 in series with RCU-014 Control unit RCU-014, inside viewChanging the cable entrance on control unit RCU-015/RCU-016 Changing cable entrance on control unit RCU-015/RCU-016Mounting dimensions for processor unit Processor UnitPower Supply Unit Mounting dimensions for power supply unitWiring Wiring OverviewFabricating signal cable RW-9600 Fabricating signal cable RW-9600Antenna unit, front view TB801 PCB 03P9436 Cable gland for signal cable RW-9600 How to wire Wago connector ProcedureHow to fasten coaxial conductor How to fabricate HV cable TYPCY-1.5 Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5Passing flat washer, etc. onto HV cable How to fabricate power cable TYPCY-2.5 Passing flat washer, etc. onto power cableFabricating the power cable DPYC-2.5 Fabricating power cable DPYC-2.5Fabricating power cable DPYC-2.5 Cable XH10P-W-6P L=20/30M Connection of cablesProcessor unit, rear view Cable XH10P-W-5P-A L=10/20/30MLocation of connectors Location of connectors inside the processor unitSignal cable RW-9600 Between antenna unit and processor unit Power cable TPYC-1.5Connection of Sub-display Port Conventional remote display FAR-2157Fabricating cable connected to terminal TB1, TB2, TB3 Power supply unit, inside viewTerminal TB1 cable DPYC-2.5 Armor Processor unit Changing AC Power SpecificationPower supply Fuse Jumper connector P108 Processor unit, inside viewHow to adjust the overvoltage detection circuit Power supply unit Power Fuse Jumper connector P8Adjustments Initializing TuningHeading Alignment Heading alignmentInitialize menu For Control Unit RCU-014For Control Unit RCU-015 Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Adjusting Sweep Timing Examples of correct and incorrect sweep timingsSuppressing Main Bang Other Settings Echo menu settingBlind Sector 1 and Blind Sector Scanner menuANT SW and ANT Stopped Radar no and Radar Posn Installation menuOn Time and TX Time LENGTH/WIDTH, Scanner Posn and SUB Scanner Posn OWN Ship Info menuGPS 1 ANT Posn and GPS 2 ANT Posn ARP W/O Gyro Not shown on IMO radar Arpa Preset menuARP-related menus ANT Select EAV w/o Gyro Other menuOther menu This page intentionally left blank Installing the Gyro Converter board Gyro Converter GC-10Fixing Gyro Converter board inside the processor unit Connecting connector assemblies inside processor unit Wiring Wago connectorAttaching plastic cover for Gyro Converter board Default setting Connection of external power supplyDIP switch, jumper wire settings Connection of external power supply to Gyro Converter boardJP1 Setting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP564P1106 Gyro Converter boardSetting the heading readout on the radar display HDG menuFlush mounting dimensions for memory card interface unit Memory Card Interface UnitOne memory card if unit and one processor unit ConnectionsDesktop mount One memory card if unit and multiple processor unitsType Code No Contents How to wire the DVI-RBG conversion board DVI-RGB Conversion KitProcessor unit, side view Processor unit bottom chassisConnecting wires to the housing BNC Connector Converter DVI-RGBInput Data Specifications Contents RemarksOutput Sentence and order of priority IEC 61162 input sentence and priorityIEC 61162 output sentence SentenceＬｉｓｔ # 70+6 000-157-497-10 工事材料表 000-155-826-10 ＰａｃｋｉｎｇＬｉｓｔ AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Marine RADAR/ARPA