Multiquip QP3TZ manual Basic Engine, Initial Servicing

Page 15

BASIC ENGINE

Figure 4. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer’s Engine manual for instructions & details of operation and servicing.

1. Fuel Filler Cap/Fuel Tank – Pull this latch to add diesel fuel to the tank. After refueling, always make sure the fuel cap is latched properly. DO NOT over fill. For additional information refer to engine owner's manual.

WARNING

Add fuel to the tank only when the engine is stopped and has cooled down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue has been completely wiped up and the area surrounding the engine is dry.

2. Engine Lifting Straps/Cover – Remove the air cleaner cover, then lift this cover (the one with decals on it) to gain access to the engine lifting straps.

3. Air Cleaner/Cover – Prevents dirt and other debris from entering the fuel system. Remove wing-nut on side of air filter cover to gain access to filter element.

6.Engine Motor Mounts – Attach these engine mounts to the pump frame.Tighten securely.

7.Oil Filter – Remove this bolt to gain access (internal) to the engine oil filter.Service the oil filter as recommended in the maintenance section of this manual.

8.Oil Drain Plugs – There are two oil drain plugs, one is underneath the flywheel, the other on the side of the engine. Remove these plugs to drain engine oil from the engine crankcase.

9.Crankshaft – Connect this shaft to the input of the transmission.

10. Muffler – Used to reduce noise and emissions.

11. Nameplate – Contains information about the engine.

WARNING

Engine components can generate extreme heat.To prevent burns, DONOTtouch these areas while the engine is running or immediatelyafteroperating.NEVERoperate the engine with the muffler removed.

4. Speed Control Lever – This lever is connected to the throttle control which is located on the side of the engine compartment cover. Use this lever to control engine speed.

5.Dipstick – Remove dipstick to determine if the engine oil level is low. If low, add oil as specified.

NOTICE

Operating the engine without an air filter, with a damaged air filter, or a filter in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

QP3TZ TRASH PUMP — OPERATION AND PARTS MANUAL — REV. #3 (10/21/11) — PAGE 15

Image 15
Contents Model QP3TZ Diesel engine exhaust and some Proposition 65 WarningQP3TZ Trash Pump Operation and Parts Manual REV. #3 10/21/11 MQ QP3TZ Trash Pump Hatz 1B30 Diesel Engine Table of ContentsOrdering parts has never been easier Parts Ordering ProcedureSafety Messages Safety InformationGeneral Safety Engine Safety Fuel Safety Transporting Safety Specifications Pump SPECIFICATIONS/DIMENSIONS PumpEngine Specifications Hatz 1B30 Specifications EngineApplication General InformationGeneral dewatering applications. Typical dewatering ComponentsInitial Servicing Basic EngineBefore Starting InspectionHoses and Clamps Understood OperationPump Vacuum Test MaintenancePump Vacuum Tester Engine Maintenance Schedule Daily Pump Storage Preparation for LONG-TERM StorageTroubleshooting Engine TroubleshootingSymptom Xxxxx only Not Used on Explanation of Code in Remarks ColumnQP3TZTRASH Pump Suggested Spare PartsPump Assy Suction Cover Pump AssyCasing Casing CoverPump Assy KEY, Impeller Bolt SET W/ Spring Washer Suction Plate M8 XBolt SET W/ Spring Washer Suction Cover M8 X Stud Bolt Drain Cover HandleSpare Parts Kits Assy Gasket SET CYL. Head Gasket SET CrankcaseEmergency KIT Accessories Assy Decal Start Accessories AssyDecal Maintenance Tool KITCrankcase and Engine Mount Assy Not Sold Separately Maintenance KITCrankcase and Engine Mount Assy Includes Items WCrankshaft Assy Stubshaft no 1 DIA Closing Plug 12 MMStubshaft no SAE GEN Stubshaft TAP 25 DIACamshaft Assy Lock Washer FlyweightCamshaft Assy CamleverPiston Assy Piston Ring SET 80MM Not Sold Separately Piston AssyCirclip Piston PINCylinder Head Assy Stud Cylinder Head 141MM Cylinder Head Cover Maintenance KITCylinder Head Assy Valve GuideOIL PUMP/GOVERNOR Assy ALL. Screw M5X12 OIL PUMP/GOVERNORRetaining Strap Ball 3.5MMOIL PUMP/GOVERNOR Assy Threaded PIN M6X18 AS Required Centrifugal WeightRing Threaded PIN M6X35 AS RequiredTiming Cover Assy Ball Bolt Governor HousingClosing Plug Main BearingFlywheel Assy Spring Washer A4 Flywheel AssyBlower Ring ALL. Screw M4X20Fuel Injection Assy Shim 1.10MM Sealing ConeShim 1.00MM Shim 1.04MMFuel Injection Assy Shim 0.2MM Connecting NippleFuel Injection Assy Control SleeveRecoil Starter Assy Allen Screw M6X10 Housing Recoil StarterRubber Sleeve Return SpringAIR Duct Assy Disc A6,4 AIR Duct AssyHood Blower DuctingAIR Duct Assy Stud M6X35 TubeStud M6X45 Sealing Strip 48MMCrankcase Breather Assy Crankcase Breather Assy Filter Breather SystemSuction Pipe Fuel Tank ASSY. OLD Style Fuel Pipe Fuel Tank ASSY. OLD StyleCAP for Fuel Tank Fuel HoseFuel Tank ASSY. NEW Style Gasket for Fuel CAP Fuel Tank ASSY. NEW StyleRope ClampFuel Tank ASSY. NEW Style Water Separator Seal WireINSUL. Hose 7 House ClipAIR Filter Assy AIR Filter AssyCover AIR Filter Sealing StripALL. Screw M8X25 NUT M6Muffler Assy CTR. Sunk Screw M6X12 Exhaust END PipeThreaded Bolt M6 Exhaust TubeSealing and Bonding Adhesives Sealing and Bonding AdhesivesFreight Policy Terms and Conditions of Sale PartsHERE’S HOW to GET Help