Lowrance electronic X67C manual Important Tip, To Restore Factory Settings

Page 41

NOTE:

If you want to change the sensitivity in Manual Mode, first turn off Auto Sensitivity: from the Sonar Page, press MENUto AUTO SENSITIVITYENTto SENSITIVITYENT. Press or to pick a different sensitivity setting. When it's set at the desired level, press EXIT.

Important Tip:

While you are experimenting and learning, it's possible to scramble the settings so that the sonar picture disappears from your screen. If that happens, remember that it's easy to switch back to full automatic operation by simply restoring the factory auto settings. Here's how:

To Restore Factory Settings

1.Press MENUMENUto RESET OPTIONSENT.

2.The unit asks if you want to reset all the options. Press or to YESENT. All options are reset, and the unit reverts back to the original settings.

Fish Symbols vs. Full Sonar Chart

You may have noticed in the quick reference that we used fish arches in full sonar chart mode for our example, and not the popular Fish I.D.fish symbol feature. Here's why.

Fish I.D. is an easier way for a sonar novice to recognize a fishy signal return when he sees it. However, locating fish by symbol only has some limitations.

Your sonar unit's microprocessor is remarkably powerful, but it can be fooled. Some of the echoes calculated to be fish could be tree limbs or turtles! To see what's under your boat in maximum detail, we recom- mend you turn off Fish I.D. and begin learning to interpret fish arches.

Fish I.D. is most handy when you're in another part of the boat or per- forming some task that prevents you from watching the sonar screen. Then, you can turn on Fish I.D. and the audible fish alarm. When that lunker swims under your boat, you'll hear it!

Fish I.D. can also be useful when you want to screen out some of the sonar detail gathered by your unit. For example, in one case fishermen in San Francisco Bay saw clouds of clutter in the water but no fish arches. When a down rigger was pulled up, it brought up several small jellyfish. The fishermen switched their Lowrance sonar to Fish I.D., which screened out the schools of jellyfish and clearly showed the game fish there as fish symbols.

37

Image 41
Contents X67C Page Table of Contents Depth Range Upper and Lower Limits Introduction Capabilities and Specifications X67CHow Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation Preparations Installation and AccessoriesShoot-through hull installations Transom installationTrolling motor installations Transom Transducer centerline Hull bottom Good location Poor location Location Poor angleDot Transom Transducer Assembly and MountingMetal Nut washer Rubber RatchetsWashers BoltBottom Hull Flat-bottom hull Deep-vee hull TransomInternal tooth washer TMB-S bracket Bolt Nut Flat washer Trolling Motor Bracket InstallationFull fish arch Proper transducer angle Transducer Orientation and Fish ArchesPartial fish arches Transducer aimed Too far back SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Spread epoxy here Sand this surface Speed/Temperature SensorsRear view Sonar unitHST-WSU Good location Transom Bottom of hull Power ConnectionsPage 76.9 Millimeter Inch 70.3 107.5 82.7Using the Quick Release Mounting Bracket Depress ratchets to release Bracket frontPPP-12 Portable Power Pack with an X67C stowed for transport Page Cup Bolt Nut Washer Transducer Tie nylon cord here SuctionCup Hull TransducerBasic Sonar Operation Exit MemoryMenus Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Bait School Thermocline With fish Fish Arches Sonar OperationsPage Important Tip To Restore Factory SettingsOther Free Training Aids ASP Advanced Signal Processing Advanced Sonar Options & Other FeaturesTo adjust and turn on the shallow alarm AlarmsBacklight Level To adjust and turn on the deep alarmTo turn the fish alarm on Calibrate Speed Chart SpeedColorLine Thin or no Colorline Wider Colorline ContrastCursor line Depth box Depth CursorDepth Range Automatic To switch to Manual Depth RangeDepth Range Manual To turn Auto Depth Range on againDepth Range Upper and Lower Limits Area zoomed FasTrackFish I.D. Fish Symbols & Depths FishTrack Symbols with FishTrack depthsHyperScroll Noise RejectionTo turn off displayed data Overlay DataTo change displayed data font size Ping Speed & HyperScrollTo adjust Sensitivity From the Sonar Page, press Menuent To turn off HyperScroll Pop-up HelpReset Water Distance Reset OptionsScreen Contrast and Backlight Level Sensitivity & Auto SensitivityAutomatic Sensitivity Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Set LanguagePress MENUMENU↓ to Software Infoent Sonar Color ModeSoftware Version Information Sonar Page & Sonar Chart Display Options Digital Data/Chart Sonar Simulator Stop ChartPress ↓ or ↑ to select clarity levelEXITEXITEXIT Surface ClarityUnits of Measure TransparencyZoom & Zoom Bar VolumeUpper and Lower Limits To turn on the Zoom Bar Zoom PanPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site
Related manuals
Manual 12 pages 37.43 Kb