Lowrance electronic X67C manual Troubleshooting

Page 72

Troubleshooting

If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page, just inside the back cover of this manual.

Unit won't turn on:

1.Check the power cable's connection at the unit. Also check the wiring.

2.Make sure the power cable is wired properly. The red wire connects to the positive battery terminal, black to negative or ground.

3.Check the fuse.

4.Measure the battery voltage at the unit's power connector. It should be at least 11 volts. If it isn't, the wiring to the unit is defective, the battery terminals or wiring on the terminals are corroded, or the bat- tery needs charging.

Unit operates only in demo mode:

1.The transducer has not yet been connected or has been disconnected. To leave demo mode, make sure the transducer is securely connected before turning the unit on.

Unit freezes, locks up, or operates erratically:

1.Electrical noise from the boat's motor, trolling motor, or an accessory may be interfering with the sonar unit. Rerouting the power and trans- ducer cables away from other electrical wiring on the boat may help. Route the sonar unit's power cable directly to the battery instead of through a fuse block or ignition switch

2.Inspect the transducer cable for breaks, cuts, or pinched wires.

3.Check both the transducer and power connectors. Make sure both are securely plugged in to the unit.

Weak bottom echo, digital readings erratic, or no fish signals:

1.Make sure the transducer is pointing straight down. Clean the face of the transducer. Oil, dirt and fuel can cause a film to form on the trans- ducer, reducing its effectiveness. If the transducer is mounted inside the hull, be sure it is shooting through only one layer of fiberglass and

that it is securely bonded to the hull. Do NOT use RTV silicone rubber adhesive or Marine-Texepoxy.

2.Electrical noise from the boat's motor can interfere with the sonar. This causes the sonar to automatically increase its Discrimination or

68

Image 72
Contents X67C Page Table of Contents Depth Range Upper and Lower Limits Capabilities and Specifications X67C IntroductionHow Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation and Accessories Installation PreparationsTransom installation Trolling motor installationsShoot-through hull installations Good location Poor location Location Poor angle Transom Transducer centerline Hull bottomTransom Transducer Assembly and Mounting DotRatchets Metal Nut washer RubberWashers BoltTransom Bottom Hull Flat-bottom hull Deep-vee hullTrolling Motor Bracket Installation Internal tooth washer TMB-S bracket Bolt Nut Flat washerTransducer Orientation and Fish Arches Partial fish arches Transducer aimed Too far backFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Speed/Temperature Sensors Spread epoxy here Sand this surfaceSonar unit Rear viewHST-WSU Good location Power Connections Transom Bottom of hullPage 107.5 82.7 76.9 Millimeter Inch 70.3Using the Quick Release Mounting Bracket Bracket front Depress ratchets to releasePPP-12 Portable Power Pack with an X67C stowed for transport Page Tie nylon cord here Suction Cup Bolt Nut Washer TransducerCup Hull TransducerBasic Sonar Operation Memory MenusExit Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesPage To Restore Factory Settings Important TipOther Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarmTo adjust and turn on the deep alarm To turn the fish alarm onBacklight Level Chart Speed Calibrate SpeedColorLine Contrast Thin or no Colorline Wider ColorlineDepth Cursor Cursor line Depth boxTo switch to Manual Depth Range Depth Range AutomaticDepth Range Manual To turn Auto Depth Range on againDepth Range Upper and Lower Limits FasTrack Area zoomedFish I.D. Fish Symbols & Depths Symbols with FishTrack depths FishTrackHyperScroll Noise RejectionOverlay Data To turn off displayed dataPing Speed & HyperScroll To change displayed data font sizeTo adjust Sensitivity From the Sonar Page, press Menuent Pop-up Help To turn off HyperScrollReset Options Reset Water DistanceScreen Contrast and Backlight Level Sensitivity & Auto SensitivityAutomatic Sensitivity Set Keel Offset Set Language Press MENUMENU↓ to SET Keel OffsetentSonar Color Mode Software Version InformationPress MENUMENU↓ to Software Infoent Sonar Page & Sonar Chart Display Options Digital Data/Chart Stop Chart Sonar SimulatorSurface Clarity Press ↓ or ↑ to select clarity levelEXITEXITEXITTransparency Units of MeasureVolume Upper and Lower LimitsZoom & Zoom Bar Zoom Pan To turn on the Zoom BarPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site
Related manuals
Manual 12 pages 37.43 Kb