Lowrance electronic X67C manual 107.5 82.7, Millimeter Inch 70.3

Page 25

ity of this kit, refer to the accessory ordering information inside the back cover of this manual.

Bracket Installation

Recommended tools for this job include: drill, 1" (25.4 mm) drill bit, screw-

driver. Required supplies for this job include: high quality, marine grade above- or below-waterline caulking compound, three #10 stainless steel screws. Screw length and type should be suitable for the material on which you intend to mount the bracket.

Mount the unit in any convenient location, provided there is clearance when it’s tilted for the best viewing angle. You should also make sure there is enough room behind the unit to attach the power/transducer cable. (See the following drawings, which show the dimensions of a gimbal-mounted X67C sonar unit.)

Holes in the bracket’s base allow wood screw or through-bolt mounting. You may need to place a piece of plywood on the back side of thin pan- els to reinforce the panel and secure the mounting hardware.

Drill a 1" (25.4 mm) hole in the dash for the power/transducer and ac- cessory cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat in- stallation. Some customers, however, prefer to mount the bracket to the side of the cable hole — it's a matter of personal preference.

107.5

[4.23]

82.7

[3.26]

156

[6.26]

12.09 [0.48]

76.9

[3.03]

Millimeter

[Inch]

70.3

[2.77]

Front view (left) and side view (right) showing dimensions

of the X67C when mounted on quick release bracket.

21

Image 25
Contents X67C Page Table of Contents Depth Range Upper and Lower Limits Introduction Capabilities and Specifications X67CHow Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation Preparations Installation and AccessoriesTrolling motor installations Transom installationShoot-through hull installations Transom Transducer centerline Hull bottom Good location Poor location Location Poor angleDot Transom Transducer Assembly and MountingMetal Nut washer Rubber RatchetsWashers BoltBottom Hull Flat-bottom hull Deep-vee hull TransomInternal tooth washer TMB-S bracket Bolt Nut Flat washer Trolling Motor Bracket InstallationPartial fish arches Transducer aimed Too far back Transducer Orientation and Fish ArchesFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Spread epoxy here Sand this surface Speed/Temperature SensorsRear view Sonar unitHST-WSU Good location Transom Bottom of hull Power ConnectionsPage 76.9 Millimeter Inch 70.3 107.5 82.7Using the Quick Release Mounting Bracket Depress ratchets to release Bracket frontPPP-12 Portable Power Pack with an X67C stowed for transport Page Cup Bolt Nut Washer Transducer Tie nylon cord here SuctionCup Hull TransducerBasic Sonar Operation Menus MemoryExit Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Bait School Thermocline With fish Fish Arches Sonar OperationsPage Important Tip To Restore Factory SettingsOther Free Training Aids ASP Advanced Signal Processing Advanced Sonar Options & Other FeaturesTo adjust and turn on the shallow alarm AlarmsTo turn the fish alarm on To adjust and turn on the deep alarmBacklight Level Calibrate Speed Chart SpeedColorLine Thin or no Colorline Wider Colorline ContrastCursor line Depth box Depth CursorDepth Range Automatic To switch to Manual Depth RangeDepth Range Manual To turn Auto Depth Range on againDepth Range Upper and Lower Limits Area zoomed FasTrackFish I.D. Fish Symbols & Depths FishTrack Symbols with FishTrack depthsHyperScroll Noise RejectionTo turn off displayed data Overlay DataTo change displayed data font size Ping Speed & HyperScrollTo adjust Sensitivity From the Sonar Page, press Menuent To turn off HyperScroll Pop-up HelpReset Water Distance Reset OptionsScreen Contrast and Backlight Level Sensitivity & Auto SensitivityAutomatic Sensitivity Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Set LanguageSoftware Version Information Sonar Color ModePress MENUMENU↓ to Software Infoent Sonar Page & Sonar Chart Display Options Digital Data/Chart Sonar Simulator Stop ChartPress ↓ or ↑ to select clarity levelEXITEXITEXIT Surface ClarityUnits of Measure TransparencyUpper and Lower Limits VolumeZoom & Zoom Bar To turn on the Zoom Bar Zoom PanPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site
Related manuals
Manual 12 pages 37.43 Kb