Lowrance electronic X67C manual Power Connections, Transom Bottom of hull

Page 23

Transom

Bottom of hull

Bottom of hull

Speed sensor mounting configuration: side view (left) and rear view (right.)

If the base of the transom has a radius, fill the gap between the tran- som and the sensor with the caulking compound. This will help ensure a smooth water flow.

Route the sensor's cable through or over the transom to the sonar unit. If you need to drill a hole in the transom to pass the connector through, the required hole size is 5/8". (The hole is 1" (25.4 mm) if you intend to route the sensor cable through the same hole as the transducer cable.)

Caution:

If you drill a hole in the transom for the cable, make sure it is lo- cated above the waterline. After installation, be sure to seal the hole with the same marine grade above- or below-waterline seal- ant used for the screws.

The sensor is now ready for use. Connect the sensor to the accessory socket on the back of the unit. If you have any questions concerning the installation of the sensor, please contact your local boat dealer.

POWER CONNECTIONS

The unit works from a 12-volt battery system. You can attach the power cable to your boat's accessory or power buss or directly to the battery. If you use an accessory buss but have problems with electrical interference, attach the power cable directly to the battery. If the cable is not long enough, splice #18 gauge wire onto it.

CAUTION:

When using the unit in a saltwater environment, we strongly rec- ommend that you shut off the power supply to the power cable when the unit is not in use. When the unit is turned off but still connected to a power supply, electrolysis can occur in the power cable plug. This may result in corrosion of the plug body along with the electri- cal contacts in the cable and the unit's power socket.

In saltwater environments we recommend you connect the power cable to the auxiliary power switch included in most boat designs.

19

Image 23

Contents X67C Page Table of Contents Depth Range Upper and Lower Limits Introduction Capabilities and Specifications X67CHow Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation Preparations Installation and AccessoriesShoot-through hull installations Transom installationTrolling motor installations Transom Transducer centerline Hull bottom Good location Poor location Location Poor angleDot Transom Transducer Assembly and MountingBolt RatchetsMetal Nut washer Rubber WashersBottom Hull Flat-bottom hull Deep-vee hull TransomInternal tooth washer TMB-S bracket Bolt Nut Flat washer Trolling Motor Bracket InstallationFull fish arch Proper transducer angle Transducer Orientation and Fish ArchesPartial fish arches Transducer aimed Too far back SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Spread epoxy here Sand this surface Speed/Temperature SensorsRear view Sonar unitHST-WSU Good location Transom Bottom of hull Power ConnectionsPage 76.9 Millimeter Inch 70.3 107.5 82.7Using the Quick Release Mounting Bracket Depress ratchets to release Bracket frontPPP-12 Portable Power Pack with an X67C stowed for transport Page Hull Transducer Tie nylon cord here SuctionCup Bolt Nut Washer Transducer CupBasic Sonar Operation Exit MemoryMenus Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Bait School Thermocline With fish Fish Arches Sonar OperationsPage Important Tip To Restore Factory SettingsOther Free Training Aids ASP Advanced Signal Processing Advanced Sonar Options & Other FeaturesTo adjust and turn on the shallow alarm AlarmsBacklight Level To adjust and turn on the deep alarmTo turn the fish alarm on Calibrate Speed Chart SpeedColorLine Thin or no Colorline Wider Colorline ContrastCursor line Depth box Depth CursorTo turn Auto Depth Range on again To switch to Manual Depth RangeDepth Range Automatic Depth Range ManualDepth Range Upper and Lower Limits Area zoomed FasTrackFish I.D. Fish Symbols & Depths Noise Rejection Symbols with FishTrack depthsFishTrack HyperScrollTo turn off displayed data Overlay DataTo change displayed data font size Ping Speed & HyperScrollTo adjust Sensitivity From the Sonar Page, press Menuent To turn off HyperScroll Pop-up HelpSensitivity & Auto Sensitivity Reset OptionsReset Water Distance Screen Contrast and Backlight LevelAutomatic Sensitivity Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Set LanguagePress MENUMENU↓ to Software Infoent Sonar Color ModeSoftware Version Information Sonar Page & Sonar Chart Display Options Digital Data/Chart Sonar Simulator Stop ChartPress ↓ or ↑ to select clarity levelEXITEXITEXIT Surface ClarityUnits of Measure TransparencyZoom & Zoom Bar VolumeUpper and Lower Limits To turn on the Zoom Bar Zoom PanPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site

Related manuals

Manual 12 pages 37.43 Kb