Phone Port, USB Port, Ethernet Port | Actiontec electronic GT701WG

Actiontec 54 Mbps Wireless DSL Gateway User Manual

Phone Port

The Phone port is used to connect the Gateway to a telephone.

USB Port

The USB port is used to connect a computer to the Gateway via USB cable.

Ethernet Port

The Ethernet port is used to connect a computer to the Gateway via Ethernet cable. The Ethernet port is a 10/100 Mbps auto-sensing port, and either a straight-through or crossover Ethernet cable can be used when connecting to the port.

Reset Switch

Depressing the Reset switch for one or two seconds will power cycle the Gateway (similar to unplugging and then plugging in the Gateway’s Power cord). To restore the Gateway’s factory default settings, depress and hold the Reset switch for approximately 10 seconds. The reset process will start about 10 seconds after releasing the switch.

Power Port

The Power port is used to connect the Power cord to the Gateway.

NWarning: Do not unplug the Power cord from the Gateway’s Power port during the reset process. Doing so may result in per- manent damage to the Gateway.

6

Image 9

Actiontec electronic GT701WG user manual Phone Port, USB Port, Ethernet Port, Reset Switch, Power Port

Contents

Wireless DSL Gateway Table of Contents Troubleshooting Setting Up a NetworkSetting Up Static IP on the Computer Specifications 111 Introduction1 Package Contents Minimum System Requirements Features Introduction Power Light Getting to Know the GatewayDSL Light Internet Light Wireless LightEthernet Light USB Light Power Port Reset SwitchPhone Port USB Port Connecting a Computer to the Gateway Setting Up GatewayPage Setting Up the Gateway Get the Gateway from the kit, then click Next Setting Up the Gateway Page Setting Up the Gateway Page Connecting Via USB Page Setting Up the Gateway Page Setting Up the Gateway Page Setting Up the Gateway Installing Phone Filters Setting Up the Gateway Page Setting Up the Gateway Click Next Ethernet Setting Up the Gateway Next, go to Setting Up the DSL Connection, below Setting Up the DSL Connection Setting Up the Gateway Page Gateway is successfully configured and ready for use Installation Buddy checks the configuration of the Gateway This page left intentionally blank Performing a Basic Setup Basic SetupTo configure the Gateway for basic operation Page Performing a Basic Setup Click Save and Restart at the bottom of the screen Changing the Admin User Name and Password Using Advanced Setup Accessing Advanced SetupTo access the Advanced Setup configuration screens Page WAN IP Address Obtain an IP Address through PPPoE or PPPoA Transparent Bridging Encapsulation PPPoA only PPP Auto Connect Specify a Static IP Address Using Advanced Setup Channel Wireless Settings WEP Off WEP+802.1x WPA Wireless MAC Authentication Wireless Advanced Settings Dhcp Server LAN IP Address Ending IP Address Beginning IP Address Services Blocking DNS Dynamic or StaticDNS Server Website Blocking Remote Management Port Forwarding DMZ Hosting Dynamic Routing Firewall Static Routing NAT Network Address Translation UPnP Universal Plug and Play Status Viewing Gateway’s SettingsPage WAN Status Routing Table Active User List LAN Status Web Activity Log Using Utilities Restore Default Settings DSL Settings Upgrade Firmware This page left intentionally blank Ethernet Setting Up a NetworkPage Setting Up a Network Page Setting Up a Network USB Setting Up a Network Page Setting Up a Network Page Wireless Page Read the on-screen instructions, then click Finish This page left intentionally blank Troubleshooting TroubleshootingCannot Use the Internet Physical Connections Connection to the Internet Frequently Asked QuestionsWhich protocols does the Gateway support? Which connection speeds does the Gateway support? Yes, the Gateway has a built-in DSL Modem Wireless Is the Gateway flash-upgradeable? How do I do it?Which wireless cards will work with the Gateway? Will my Xbox work with the Gateway? How do I find out which IP address my computer is using? What is the valid IP range I can use for my home network? Yes, if the application is designed to run over a network What is NAT and how does it protect my network? What is the default username for the Gateway?How many computers can be connected through the Gateway? Does the Gateway function as a firewall? Locating Computer Information Reference Locating Windows Operating System Files Appendix a Reference Click Search Windows 98 SE Setting Up Static IP On the ComputerPage 192.168.0.2 Enter the following address in the Subnet mask text box Windows Me Appendix B Setting Up Static IP on the Computer 192.168.0.2 Windows Page Appendix B Setting Up Static IP on the Computer 100 Windows XP 102 103 104 105 106 Computer Security Comparing DSL Service with a Dial-Up Modem Gateway Security Computer SecurityInternet Browsers Electronic Security 110 General Specifications DLite T1.413 RFC 1483, 2364 Protocol WAN PPP, DHCP, Static IP LED Indicators Wireless Operating RangePower, DSL, Internet, Ethernet, USB, Wireless Environmental Glossary Access Point 114 Ssid 116 High Security Level Firewall Security Level Services Table Low Security Level Medium Security Level Basic Security Level Service Acronym Definitions Icmp Real audio/video323 120 Classic Non-Windows G System Setup 122 Appendix G Non-Windows Setup 124 Installation Buddy Settings Default Mode PPPoA Default VPI Default VCI Regulatory Compliance Notices ModificationsClass B Equipment All other names are the property of their respective owners Miscellaneous Legal Notices 129 Limited Warranty 130 Limited Warranty 132