Lowrance electronic X67C manual Transducer Orientation and Fish Arches

Page 16

3.Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the troll- ing motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the sonar unit and the trans- ducer is ready for use.

Transducer mounted on trolling motor, side view.

TRANSDUCER ORIENTATION AND FISH ARCHES

If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds.

Partial fish arches

Transducer aimed	Transducer aimed
too far back	too far forward

Full fish arch

Proper transducer angle

Transducer angles and their effects on fish arches.

12

Image 16

Contents X67C Page Table of Contents Depth Range Upper and Lower Limits Capabilities and Specifications X67C IntroductionHow Sonar Works How to use this manual typographical conventions Press ↓ to Fish ID Symbolsentexitexit Installation and Accessories Installation PreparationsTrolling motor installations Transom installationShoot-through hull installations Good location Poor location Location Poor angle Transom Transducer centerline Hull bottomTransom Transducer Assembly and Mounting DotRatchets Metal Nut washer RubberWashers BoltTransom Bottom Hull Flat-bottom hull Deep-vee hullTrolling Motor Bracket Installation Internal tooth washer TMB-S bracket Bolt Nut Flat washerPartial fish arches Transducer aimed Too far back Transducer Orientation and Fish ArchesFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Speed/Temperature Sensors Spread epoxy here Sand this surfaceSonar unit Rear viewHST-WSU Good location Power Connections Transom Bottom of hullPage 107.5 82.7 76.9 Millimeter Inch 70.3Using the Quick Release Mounting Bracket Bracket front Depress ratchets to releasePPP-12 Portable Power Pack with an X67C stowed for transport Page Tie nylon cord here Suction Cup Bolt Nut Washer TransducerCup Hull TransducerBasic Sonar Operation Menus MemoryExit Main Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesPage To Restore Factory Settings Important TipOther Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarmTo turn the fish alarm on To adjust and turn on the deep alarmBacklight Level Chart Speed Calibrate SpeedColorLine Contrast Thin or no Colorline Wider ColorlineDepth Cursor Cursor line Depth boxTo switch to Manual Depth Range Depth Range AutomaticDepth Range Manual To turn Auto Depth Range on againDepth Range Upper and Lower Limits FasTrack Area zoomedFish I.D. Fish Symbols & Depths Symbols with FishTrack depths FishTrackHyperScroll Noise RejectionOverlay Data To turn off displayed dataPing Speed & HyperScroll To change displayed data font sizeTo adjust Sensitivity From the Sonar Page, press Menuent Pop-up Help To turn off HyperScrollReset Options Reset Water DistanceScreen Contrast and Backlight Level Sensitivity & Auto SensitivityAutomatic Sensitivity Set Keel Offset Set Language Press MENUMENU↓ to SET Keel OffsetentSoftware Version Information Sonar Color ModePress MENUMENU↓ to Software Infoent Sonar Page & Sonar Chart Display Options Digital Data/Chart Stop Chart Sonar SimulatorSurface Clarity Press ↓ or ↑ to select clarity levelEXITEXITEXITTransparency Units of MeasureUpper and Lower Limits VolumeZoom & Zoom Bar Zoom Pan To turn on the Zoom BarPage Troubleshooting Page Noise Page Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site

Related manuals

Manual 12 pages 37.43 Kb