Fujitsu MB96300 manual Table of hazardous substances name and concentration

Page 35

SK-96370-144PMC-GDC User Guide

Chapter 8 China-RoHS regulation

In order to maintain the declared EFUP, the product shall be operated normally according to the instructions and environmental conditions as defined in the product manual, and periodic maintenance schedules specified in Product Maintenance Procedures shall be followed strictly.

Consumables or certain parts may have their own label with an EFUP value less than the product. Periodic replacement of those consumables or parts to maintain the declared EFUP shall be done in accordance with the Product Maintenance Procedures.

This product must not be disposed of as unsorted municipal waste, and must be collected separately and handled properly after decommissioning.

Please note: The designation of 10 years EFUP is not to be equated with the durability, use- duration or any warranty-claims of the product.

Table of hazardous substances name and concentration

Hazardous substances name

Component Name

 

(Pb)

(Hg)

(Cd)

(Cr(VI))

(PBB)

(PBDE)

SK-96370-144PMC-GDC

x

o

o

o

o

o

O:

SJ/T11363-2006

X:

SJ/T11363-2006

O:Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363-2006.

X:Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.

Data listed in the table represents best information available at the time of publication

© Fujitsu Microelectronics Europe GmbH

- 35 -

FMEMCU-UG-960014-10

Image 35
Contents MB96300 Series Revision History Date IssueNo Liability for Consequential Damages Warranty and DisclaimerContents Programming the Internal Flash Memory Abstract OverviewFeatures General Description Emulation System 8 I2C BusEmulator System Do not use any other probe cable than MB2198-507-E only InstallationConnection/Power-On Jumper Description / Function Type Default Coordinates Default Jumper settings for MB96370 SeriesFlash / Lime Jumper SettingsJumper Location Default Jumper SettingsMCU Operating Mode Jumpers and SwitchesOperating Mode S1 Mcuvcc Power Supply S2, JP 8, 15, 16, 17Power Supply Configuration JP8JP2 Subclock JP 1JP1 JP2ADC Supply Analog Power Supply Voltage JP 11, 12, 13Alarm Comparator JP Alarm ComparatorRST MCU Reset Generation JP 33, 41, 46, 47Uart Reset Reset ConnectionUser Push Buttons User Buttons SW1, SW2, SW3, SW4, SW5, SW6 JP 3, 4, 5, 6I2C pull-up resistor JP 9 LIN-UART 0 JP 19, 21, 23, 25, 27, 28, 29 UART0 SettingsLIN / Uart Can interfaces JP 24, 26, 34 UART2 SettingsCan Settings LIN-UART 2 JP 36, 37, 38, 39, 40, 42, 43External Sram memory JP 50, 53 10 External Flash Configuration11 Flash Configuration Jumpers External Flash memory JP 49, 5212 Graphic Display Controller interface GlrstFlrst LIN-UART connectors X5 ConnectorsPower connector MCU pin header connectors X20A, X20B, X21, X22Canh Can Connector X6Can Connector Signals CanlUser LEDs/LCD USER-LEDs & optional LC-Display J1SIN3 In-Circuit-Programming ConnectorMD0 RstxExternal Supply Voltage Vin J3 Alarm Comparator Connector J2VCC Connector J7 GND Connector J8Programming the internal Flash memory Asynchronous ModeJumper Settings for Programming via Uart 0 Jumper Settings for Programming via Uart 2Flash Programming Reset optionalJumper Settings for reset signal Flash Programming Socket Synchronous ModeRelated Products AppendixHttp//mcu.emea.fujitsu.com Information in the WWWEvaluation Board Emulation Board China-RoHS regulationTable of hazardous substances name and concentration Valid for European Union Countries RecyclingGültig für EU-Länder